ID.4 2021 ➤
Running gear, axles, steering - Edition 05.2021
– On both sides of vehicle, replace bolts on subframe -1- one
after other with locating pins -T10096--A-, and tighten these
to 20 Nm.
Installing
Install in reverse order of removal, observing the following:
– Always unscrew one locating pin -T10096- at a time, replace
it with a new bolt, and only then proceed with the next one.
Tightening torques
♦ ⇒ Running gear, axles, steering; Rep. gr. 42; Subframe; As‐
sembly overview – subframe
♦ ⇒ General body repairs, exterior; Rep. gr. 66; Underbody
cladding; Assembly overview – underbody cladding
3.2
Assembly overview – subframe mountings
1 - Right motor mounting
❑ ⇒ Rep. gr. 42; Renew‐
ing motor mounting
2 - Subframe
❑ ⇒ Rep. gr. 42; As‐
sembly overview – sub‐
frame
❑ ⇒ Rep. gr. 42; Fixing
subframe in position
❑ ⇒ Rep. gr. 42; Taking
up weight of subframe
using scissor-type as‐
sembly platform
❑ ⇒ Rep. gr. 42; Remov‐
ing and installing rear
axle
3 - Subframe mounting, rear
right
❑ ⇒ Rep. gr. 42; Re‐
newing rear subframe
mountings
4 - Gearbox mounting
❑ ⇒ Rep. gr. 42; Renew‐
ing gearbox mounting
5 - Subframe mounting, rear
left
❑ ⇒ Rep. gr. 42; Re‐
newing rear subframe
mountings
6 - Left motor mounting
❑ ⇒ Rep. gr. 42; Renew‐
ing motor mounting
7 - Subframe mountings, front
left
❑ ⇒ Rep. gr. 42; Renewing front subframe mountings
8 - Subframe mounting, front right
❑ ⇒ Rep. gr. 42; Renewing front subframe mountings
104
Rep. gr.42 - Rear suspension
ID.4 2021 ➤
Running gear, axles, steering - Edition 05.2021
3.3
Assembly overview – subframe
1 - Bolt
❑ M 6 × 25
❑ 8 Nm
2 - Bracket
3 - Bolt
❑ qty. 4
❑ Renew after removing
❑ M14 × 1.5 × 125
❑ 130 Nm +180°
4 - Subframe
❑ ⇒ Rep. gr. 42; Fixing
subframe in position
❑ ⇒ Rep. gr. 42; Taking
up weight of subframe
using scissor-type as‐
sembly platform
❑ ⇒ Rep. gr. 42; Remov‐
ing and installing rear
axle
5 - Bracket
6 - Bolt
❑ M 6 × 25
❑ 8 Nm
3.4
Preparing scissor-type assembly plat‐
form
Special tools and workshop equipment required
♦ Basic set for Phaeton -VAS 6131/1-
♦ Plate -VAS 6131/10-1-
♦ Scissor-type assembly platform -VAS 6131B-
♦ Support -VAS 6131/1-4-
♦ Support set for Audi -VAS 6131/10-5-
♦ Support set for natural gas tank -VAS 6131/15-
♦ Support taper -VAS 6131/10-2-
♦ Universal support -VAS 6131/13-2-
♦ scissor-type assembly platform -VAS 6131B-
♦ support -VAS 6131/1-4-
3. Subframe
105
2024 VW ID.4 Owner's Manual
