ID.4 2021 ➤
Running gear, axles, steering - Edition 05.2021
Removing
– ⇒ Rep. gr. 40; Prepare scissor-type assembly platform.
– Position scissor-type assembly platform -VAS 6131B--A-
longitudinally under vehicle, align it, and raise it.
– Position supports -2- and -4- on subframe -1- as shown in
illustration.
– Adjust height of supports -2- and -4-.
– Raise scissor-type assembly platform -VAS 6131B--A- fur‐
ther.
– Align supports -4- with holes on right side of subframe -1-.
– Align supports -2- with holes on left side of subframe -1-.
– Tighten bolts for supports -2- and -4- on scissor-type assem‐
bly platform -VAS 6131B--A- to 40 Nm.
– Align support -3- with cross member at rear of subframe -1-.
– Align height of supports -2-, -3- and -4-, and bolt them on.
– Raise scissor-type assembly platform -VAS 6131B- further,
and support subframe -1-.
3.5
Preparing scissor-type assembly plat‐
form
Special tools and workshop equipment required
♦ Plate -VAS 6131/10-1-
♦ Scissor-type assembly platform -VAS 6131B-
♦ Spindle -VAS 6131/10-5-
♦ Support set for Audi -VAS 6131/10-7-
♦ Universal support -VAS 6131/13-2-
♦ scissor-type assembly platform -VAS 6131B-
Removing
Prepare supports 1:
– Assemble supports as shown using the following tools:
14
Rep. gr.40 - Front suspension
ID.4 2021 ➤
Running gear, axles, steering - Edition 05.2021
1 - Adapter Support set for Audi -VAS 6131/10-7-
2 - Spindle -VAS 6131/10-5-
3 - Support taper Support set for Audi -VAS 6131/10-4-
4 - Plate -VAS 6131/10-1-
5 - Scissor-type assembly platform -VAS 6131B-
6 - Bolt M 10 x 25 Support set for Audi -VAS 6131/10-
Prepare support 2:
– Assemble support as shown using the following tools:
1 - Universal support -VAS 6131/13-2-
2 - Spindle -VAS 6131/10-5-
3 - Support taper Support set for Audi -VAS 6131/10-4-
4 - Plate -VAS 6131/10-1-
5 - Scissor-type assembly platform -VAS 6131B-
6 - Bolt M 10 x 25 Support set for Audi -VAS 6131/10-
3. Subframe
15
ID.4 2021 ➤
Running gear, axles, steering - Edition 05.2021
– Screw bolts for supports by hand into scissor-type assem‐
bly platform -VAS 6131B--3-. Position scissor-type assembly
platform -VAS 6131B--3- horizontally.
Coordinates Support
E 10
B 12
G 12
C 15
F 15
2
1
1
1
1
Note
The supports can also be mounted at other coordinates. Dis‐
tance between the individual supports must be exactly as speci‐
fied.
– Note spirit level on scissor-type assembly platform -VAS
6131B--3-.
3.6
Supporting components in vehicle front
end in installation position
Special tools and workshop equipment required
♦ Adapter -10-222A/19-
♦ Bracket -T10346/1-
♦ Hook -10-222A/20-
♦ Square tube -T40091/1-
♦ Support bracket -10-222A-
♦ Tensioning strap -T10523-
♦ support bracket -10-222A-
Removing
– Remove air intake unit of heater and air conditioning
unit⇒ Heating, air conditioning system; Rep. gr. 87; Front
heater and air conditioning unit; Removing and installing air
intake unit of heater and air conditioning unit
– Detach cap -1- from bumper.
16
Rep. gr.40 - Front suspension
2024 VW ID.4 Owner's Manual
