ID.4 2021 ➤
Running gear, axles, steering - Edition 05.2021
8
Anti-roll bar
8.1
Assembly overview – anti-roll bar
1 - Nut
❑ M14 × 1.5
❑ 160 Nm
2 - Suspension strut
❑ ⇒ Rep. gr. 40; Assem‐
bly overview – suspen‐
sion strut
❑ ⇒ Rep. gr. 40; Remov‐
ing and installing sus‐
pension strut
3 - Coupling rod
❑ ⇒ Rep. gr. 40; Remov‐
ing and installing cou‐
pling rod
4 - Bolt
❑ Qty. 4
❑ Renew after removing
❑ M 10 x 75
❑ 20 Nm +180°
5 - Subframe
❑ ⇒ Rep. gr. 40; As‐
sembly overview – sub‐
frame
❑ ⇒ Rep. gr. 40; Re‐
moving and installing
subframe with steering
rack
❑ ⇒ Rep. gr. 40; Fixing
subframe in position
6 - Anti-roll bar
❑ ⇒ Rep. gr. 40; Remov‐
ing and installing anti-
roll bar
7 - Bonded rubber bush
❑ Part of anti-roll bar
8.2
Removing and installing anti-roll bar
Removing
Removal and installation are described for the left side of vehi‐
cle as an example.
– ⇒ Rep. gr. 44; Remove wheel.
– Remove underbody cladding at front ⇒ General body re‐
pairs, exterior; Rep. gr. 66; Underbody cladding; Removing
and installing underbody cladding.
8. Anti-roll bar
85
ID.4 2021 ➤
Running gear, axles, steering - Edition 05.2021
– Remove front left and front right wheel housing liners ⇒ Gen‐
eral body repairs, exterior; Rep. gr. 66; Wheel housing liner;
Removing and installing front wheel housing liner.
– Remove radiator cowl with radiator fan ⇒ Electric rear-wheel
drive EIP220 and all-wheel drive EIA200, EIP220; Rep.
gr. 19; Radiator/radiator fan; Removing and installing radia‐
tor cowl with radiator fan.
– Disconnect electrical connector -1- on refrigerant pressure
and temperature sender 3 -G827--2-.
– Unscrew nut -5- for coupling rods -2- from anti-roll bar -1- on
both vehicle sides. Counterhold on multi-point socket head
on coupling rod -1- when doing this.
– Unscrew bolts -6- from bearings -4-.
– Remove anti-roll bar -1- from subframe -3-, and guide it out.
Installing
Install in reverse sequence of removal.
Tightening torques
♦ ⇒ a8.3 nd installing coupling rod”, page 87
♦ ⇒ Rep. gr. 19; Radiator/radiator fans; Assembly overview –
radiator cowl and radiator fans
♦ ⇒ General body repairs, exterior; Rep. gr. 66; Wheel housing
liner; Assembly overview – front wheel housing liner
86
Rep. gr.40 - Front suspension
ID.4 2021 ➤
Running gear, axles, steering - Edition 05.2021
♦ ⇒ General body repairs, exterior; Rep. gr. 66; Underbody
cladding; Assembly overview – underbody cladding
♦ ⇒ Wheels and Tyres Guide; Rep. gr. 44; Wheels, tyres;
Specified torque for wheel bolts
8.3
Removing and installing coupling rod
Removal and installation are described for the left side of vehi‐
cle as an example.
Removing
– ⇒ Rep. gr. 44; Remove wheel.
– Unscrew nut -3-. Counterhold on multi-point socket head on
coupling rod -1- when doing this.
– Pull coupling rod -1- off suspension strut -2-.
– Unscrew nut -3- from coupling rod -1-. Counterhold on multi-
point socket head on coupling rod -1- when doing this.
– Pull coupling rod -1- out of anti-roll bar -2-.
Installing
Install in reverse order of removal, observing the following:
Tightening torques
♦ ⇒ Rep. gr. 40; Assembly overview – anti-roll bar
♦ ⇒ Wheels and Tyres Guide; Rep. gr. 44; Wheels, tyres;
Specified torque for wheel bolts
8. Anti-roll bar
87
2024 VW ID.4 Owner's Manual
