Table of Contents > Rear suspension > 5 Suspension link, track rod > 5.9 Removing and installing upper front suspension link

VW ID.4 Running Gear, Axles, Steering ➜ 5.9 Removing and installing upper front suspension link

ID.4 2021 ➤  
Running gear, axles, steering - Edition 05.2021  
– Unscrew bolt -2- from wheel bearing housing -1-.  
– Pull bolt -4- out of subframe -6-.  
– Remove upper rear suspension link -3-.  
Installing  
Install in reverse order of removal, observing the following:  
– Suspension link must be bolted on only in unladen position  
⇒ Rep. gr. 42; Raising wheel bearing assembly to unladen  
position.  
– Perform wheel alignment ⇒ Rep. gr. 44; Necessity of wheel  
alignment.  
Tightening torques  
♦ ⇒ Rep. gr. 42; Assembly overview – suspension link  
♦ ⇒ Rep. gr. 42; Assembly overview – anti-roll bar  
♦ ⇒ General body repairs, exterior; Rep. gr. 63; Rear bumper;  
Assembly overview – bumper cover  
♦ ⇒ General body repairs, exterior; Rep. gr. 66; Underbody  
cladding; Assembly overview – underbody cladding  
♦ ⇒ Wheels and Tyres Guide; Rep. gr. 44; Wheels, tyres;  
Specified torque for wheel bolts  
5.9  
Removing and installing upper front  
suspension link  
Special tools and workshop equipment required  
♦ engine and gearbox jack -VAS 6931-  
♦ gearbox support -T10337-  
Removing  
– ⇒ Rep. gr. 44; Remove wheel.  
– Remove rear centre underbody cladding ⇒ General body re‐  
pairs, exterior; Rep. gr. 66; Underbody cladding; Removing  
and installing rear centre underbody cladding.  
– Position engine and gearbox jack -VAS 6931--B- with gear‐  
box support -T10337--A- under wheel bearing housing -1-,  
and push upwards slightly to provide support.  
158  
Rep. gr.42 - Rear suspension  
ID.4 2021 ➤  
Running gear, axles, steering - Edition 05.2021  
– Unscrew nut -4-.  
– Pull bolt -2- out of wheel bearing housing -3-.  
– Unscrew nut -6-.  
– Pull bolt -5- out of subframe -7-.  
– Remove upper front suspension link -1-.  
Installing  
Install in reverse order of removal, observing the following:  
– Suspension link must be bolted on only in unladen position  
⇒ Rep. gr. 42; Raising wheel bearing assembly to unladen  
position.  
– Perform wheel alignment ⇒ Rep. gr. 44; Necessity of wheel  
alignment.  
Tightening torques  
♦ ⇒ Rep. gr. 42; Assembly overview – suspension link  
♦ ⇒ General body repairs, exterior; Rep. gr. 66; Underbody  
cladding; Assembly overview – underbody cladding  
5. Suspension link, track rod  
159  
ID.4 2021 ➤  
Running gear, axles, steering - Edition 05.2021  
♦ ⇒ Wheels and Tyres Guide; Rep. gr. 44; Wheels, tyres;  
Specified torque for wheel bolts  
160  
Rep. gr.42 - Rear suspension  

Need help?

If after viewing the owner's manual or service manual you still have some unresolved questions about the car VW ID.4 you can write to us using the link below, describing your problem in detail, we try to answer all questions.


Ask your question on the page - Support!