ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
– Observe pressure sensor -C- for approx. 5 minutes. The
pressure must not drop by more than 1 mbar. Pressure fluc‐
tuations are normal.
– If the pressure drops by more than 1 mbar locate the leak
using a commercially available leak detection spray.
Important
•
•
If leaks have been located and sealed, repeat leakage test.
If no leakage was detected, remove all tools.
7.3
Assembly overview – electric drive mo‐
tor
7.3.1
Assembly overview – electric drive motor, rear motor
232
Rep. gr.93 - Electric drive systems
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
1 - Power and control elec‐
tronics for electric drive -JX1-
❑ With electric drive con‐
trol unit -J841-
❑ With intermediate cir‐
cuit capacitor 1 -C25-
❑ With DC/AC converter
for drive motor -A37-
❑ ⇒ Rep. gr. 93; Remov‐
ing and installing power
and control electronics
for electric drive, rear-
wheel drive
2 - Bolt
❑ Qty. 4
❑ Renew after removing
❑ 16 Nm +135°
3 - Connecting piece
❑ Renew after removing
4 - Dowel sleeve
❑ Qty. 2
5 - Three-phase current drive
-VX54- with gearbox
❑ With electric drive mo‐
tor -V141-
❑ ⇒ Rep. gr. 10; Remov‐
ing rear motor
6 - Drive motor rotor position
sender 1 -G713-
❑ With temperature send‐
er for drive motor -
G712-
❑ ⇒ Rep. gr. 93; Remov‐
ing and installing drive motor rotor position sender, rear-wheel drive
7 - Bolt
❑ Qty. 6
❑ Renew after removing
❑ 4 Nm +90°
8 - Cover
❑ Renew after removing
9 - Bolt
❑ Qty. 7
❑ Renew after removing
❑ Specified torque and tightening sequence ⇒ page 234
10 - Centre hex stud
❑ Qty. 2
❑ Renew after removing
❑ Specified torque and tightening sequence ⇒ page 234
11 - Clamping washer
❑ Qty. 2
12 - Insulation
7. Electric drive motor
233
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
13 - Bolt
❑ Qty. 3
❑ Renew after removing
❑ 8 Nm +90°
Cover – specified torque and tightening sequence
Stage Bolts
Specified torque/turning further angle
-1- to -9- tighten by hand up to stop
-1- to -9- 8 Nm
-1- to -9- 45°
1
2
3
7.3.2
Assembly overview – electric drive motor, front motor
234
Rep. gr.93 - Electric drive systems
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
1 - Bleeder valve
2 - Power and control elec‐
tronics 2 for electric drive -
JX4-
❑ With electric drive con‐
trol unit 2 -J944-
❑ With intermediate cir‐
cuit capacitor 2 -C26-
❑ With DC/AC converter
for drive motor 2 -A55-
❑ ⇒ Rep. gr. 93; Remov‐
ing and installing power
and control electronics
for electric drive, rear-
wheel drive
3 - Bolt
❑ Qty. 2
❑ Renew after removing
❑ 30 Nm +45°
4 - Connecting piece
❑ Renew after removing
5 - Gasket
❑ Renew after removing
6 - Dowel pins
❑ Qty. 2
❑ Renew after removing
7 - Three-phase current drive
2 -VX97- with gearbox
❑ With electric drive mo‐
tor 2 -V717-
8 - Seal
9 - O-ring
❑ Renew after removing
10 - Coolant connection
11 - Bolt
❑ Qty. 2
❑ Renew after removing
❑ 5 Nm
12 - Rotor position sender 1 for drive motor 2 -G1147-
❑ With temperature sender for drive motor 2 -G1146-
❑ ⇒ Rep. gr. 93; Removing and installing drive motor rotor position sender, rear-wheel drive
13 - Bolt
❑ Qty. 2
❑ 3.5 Nm
14 - Oil drain plug
❑ Renew after removing
❑ 15 Nm
15 - Seal
❑ Renew after removing
7. Electric drive motor
235
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
16 - Bearing plate with shaft
17 - Seal
18 - Bolt
❑ Qty. 7
❑ Renew after removing
19 - Seal
20 - Plug
❑ Renew after removing
❑ 15 Nm
21 - Gasket
❑ Renew after removing
22 - Bolt
❑ Qty. 2
❑ Renew after removing
❑ 30 Nm +45°
23 - Bolt
❑ Tighten in diagonal sequence
❑ Qty. 4
❑ Renew after removing
❑ 6 Nm
24 - Cover
❑ Renew after removing
25 - Bolt for bus bar
❑ Qty. 3
❑ Renew after removing
❑ 9 Nm
26 - O-ring
❑ Renew after removing
27 - Bolt
❑ Qty. 2
❑ 5 Nm
28 - Coolant connection
Bearing plate – specified torque and tightening sequence
236
Rep. gr.93 - Electric drive systems
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
Stage Bolts
Specified torque/turning further angle
1
2
-1- to -7- tighten by hand up to stop
-1- to -7- 6 Nm
7.4
Removing and installing drive motor ro‐
tor position sender, rear-wheel drive
7.4.1
Removing and installing drive motor ro‐
tor position sender 1 [G713]
The drive motor rotor position sender 1 -G713- will henceforth
be referred to as “sender”.
Note
Bolts could fall into the motor. Turn the motor to horizontal
position.
Removing
– Remove power and control electronics for electric drive -
JX1- ⇒ Rep. gr. 93; Removing and installing power and con‐
trol electronics for electric drive, rear-wheel drive.
– Unscrew bolts -arrows- for sender -A-.
– Pull sender -A- off connection -2- -arrow-.
Installing
– Fit sender -A- onto connection -2- -arrow-.
7. Electric drive motor
237
2024 VW ID.4 Owner's Manual
