ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
2
Removing and installing front motor
2.1
2.1.1
Assembly overview – front motor
Assembly overview – front motor, left-hand drive vehicles
2. Removing and installing front motor
15
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
1 - Three-phase current
drive 2 -VX97-
❑ With electric drive mo‐
tor 2 -V717-
❑ With temperature send‐
er for drive motor 2 -
G1146-
❑ With rotor position
sender 1 for drive mo‐
tor 2 -G1147-
❑ With power and control
electronics 2 for electric
drive -JX4-
❑ ⇒ Rep. gr. 93; Remov‐
ing and installing power
and control electronics
for electric drive, rear-
wheel drive
❑ ⇒ Rep. gr. 10; Remov‐
ing front motor
❑ ⇒ Rep. gr. 10; Installing
front motor
2 - Bolt for gearbox mounting
❑ Renew after removing
❑ 70 Nm +90°
3 - Bolt for gearbox support
❑ Qty. 3
❑ Renew after removing
❑ 50 Nm +90°
4 - Gearbox support
5 - Gearbox breather line
6 - Bolt for gearbox mounting
❑ Qty. 2
❑ Renew after removing
❑ 50 Nm +90°
7 - Gearbox mounting
❑ ⇒ Rep. gr. 10; Removing and installing gearbox mountings
8 - High-voltage connector for power and control electronics 2 for electric drive -JX4-
9 - High-voltage cable duct
10 - Bolt for cable guide
❑ Qty. 3
❑ 8 Nm
11 - Bolt for potential equalisation line
❑ 8 Nm
12 - Electrical connector for power and control electronics 2 for electric drive -JX4-
13 - Potential equalisation line
14 - Motor support
15 - Front motor mounting
❑ ⇒ Running gear, axles, steering; Rep. gr. 40; Subframe; Renewing front motor mounting
16 - Bolt for motor mounting
16
Rep. gr.10 - Removing and installing engine
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
❑ Renew after removing
❑ 130 Nm +180°
17 - Bolt for motor support
❑ Qty. 3
❑ Renew after removing
❑ 50 Nm +90°
18 - Bolt for motor support
❑ Qty. 3
❑ Renew after removing
❑ 50 Nm +90°
19 - Bolt for motor mounting
❑ Renew after removing
❑ 130 Nm +180°
20 - Front motor mounting
❑ ⇒ Running gear, axles, steering; Rep. gr. 40; Subframe; Renewing front motor mounting
21 - Motor support
Assembly overview – noise insulation, motor
1 - Retaining clip
2 - Clip
- Qty. 2
3 - Clip
- Qty. 2
4 - Three-phase current drive 2 -VX97-
5 - Noise insulation
- Depending on equipment/version
6 - Retaining clip
2.1.2
Assembly overview – front motor, right-hand drive vehicles
2. Removing and installing front motor
17
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
1 - Three-phase current
drive 2 -VX97-
❑ With electric drive mo‐
tor 2 -V717-
❑ With temperature send‐
er for drive motor 2 -
G1146-
❑ With rotor position
sender 1 for drive mo‐
tor 2 -G1147-
❑ With power and control
electronics 2 for electric
drive -JX4-
❑ ⇒ Rep. gr. 93; Remov‐
ing and installing power
and control electronics
for electric drive, rear-
wheel drive
❑ ⇒ Rep. gr. 10; Remov‐
ing front motor
❑ ⇒ Rep. gr. 10; Installing
front motor
2 - Bolt for gearbox mounting
❑ Renew after removing
❑ 70 Nm +90°
3 - Bolt for gearbox support
❑ Qty. 3
❑ Renew after removing
❑ 50 Nm +90°
4 - Gearbox support
5 - Gearbox breather line
6 - Bolt for gearbox mounting
❑ Qty. 2
❑ Renew after removing
❑ 50 Nm +90°
7 - Gearbox mounting
❑ ⇒ Rep. gr. 10; Removing and installing gearbox mountings
8 - High-voltage connector for power and control electronics 2 for electric drive -JX4-
9 - High-voltage cable duct
10 - Bolt for cable guide
❑ Qty. 3
❑ 8 Nm
11 - Bolt for potential equalisation line
❑ 8 Nm
12 - Electrical connector for power and control electronics 2 for electric drive -JX4-
13 - Potential equalisation line
14 - Cover plate
15 - Bolt
❑ Qty. 3
❑ 8 Nm
18
Rep. gr.10 - Removing and installing engine
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
16 - Bolt for motor support
❑ Qty. 2
❑ Renew after removing
❑ 50 Nm +90°
17 - Front motor mounting
❑ ⇒ Running gear, axles, steering; Rep. gr. 40; Subframe; Renewing front motor mounting
18 - Bolt for front motor mounting
❑ Renew after removing
❑ 130 Nm +180°
19 - Bolt for motor support
❑ Qty. 2
❑ Renew after removing
❑ 50 Nm +90°
20 - Bolt for front motor mounting
❑ Renew after removing
❑ 130 Nm +180°
21 - Front motor mounting
❑ ⇒ Running gear, axles, steering; Rep. gr. 40; Subframe; Renewing front motor mounting
22 - Motor support
2.2
Removing front motor
2.2.1
Removing front motor, left-hand drive
vehicles
Special tools and workshop equipment required
♦ engine bung set -VAS 6122-
♦ lifting tackle -VAS 501 021-
♦ workshop hoist -VAS 6100-
The three-phase current drive 2 -VX97- along with the power
and control electronics 2 for electric drive -JX4- will henceforth
be referred to as “motor”.
Removing
Once the drive shafts have been removed, seal the drive shaft
flange using sealing plugs from engine bung set -VAS 6122-.
Important
•
There must be no gear oil running out.
– Remove subframe together with motor ⇒ Running gear,
axles, steering; Rep. gr. 40; Subframe; Removing and instal‐
ling subframe with motor.
– Insert bracket of lifting tackle -VAS 501 021--A- into holes
-arrows B-.
2. Removing and installing front motor
19
2024 VW ID.4 Owner's Manual
