ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
Important
•
The aid of an additional mechanic is required for the subse‐
quent work steps.
– Lift out radiator module from radiator mountings.
Installing
Install in reverse order of removal, observing the following:
– Connect refrigerant lines to condenser/gas cooler ⇒ Heating,
air conditioning; Rep. gr. 87; Refrigerant circuit; Disconnect‐
ing refrigerant lines from and connecting to condenser/gas
cooler.
– Move bumper carrier back from service position ⇒ General
body repairs, exterior; Rep. gr. 63; Front bumper; Moving
bumper carrier to and back from service position.
Tightening torques
♦ ⇒ Rep. gr. 19; Assembly overview - radiator/radiator fan
4.4
Dismantling and assembling radiator
module
Dismantling radiator module
– Remove radiator module ⇒ Rep. gr. 19; Removing and in‐
stalling radiator module.
– Press in retaining tabs -1- for radiator cowl on both sides in
direction of -arrow A-.
96
Rep. gr.19 - Cooling
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
– Pull radiator cowl -2- off radiator upwards in direction of
-arrow B-.
– Disconnect air ducts -1- and -2-. To do so, release fasteners
-arrows-.
– Also release lower fasteners -3-. Pull air ducts -1- and -2-
apart.
Important
•
Radiator roller blind -2- must be pulled 15 mm out of fasten‐
er for condenser/gas cooler to be removed.
NOTICE
Risk of damage to material shaft of radiator roller blind.
– Only pull or push on outside of radiator roller blind frame.
– Press in retaining tabs -1- for radiator roller blind -2- on both
sides in direction of -arrow A-.
– Take hold of outside of radiator roller blind -2- and pull it
15 mm upwards out of fastener in direction of -arrow B-.
4. Radiator, radiator fan
97
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
– Press in retaining tabs -1- for condenser/gas cooler on both
sides in direction of -arrow A- and remove condenser/gas
cooler -2-.
– Pull condenser/gas cooler -2- upwards off radiator in direc‐
tion of -arrow B-.
– Detach radiator roller blind from radiator.
Assembling radiator module
– Bring radiator roller blind -1- into installation position
-arrows- on radiator -2-, but do not engage radiator roller
blind yet.
– Install and engage condenser/gas cooler -2-. Check it is
securely engaged by pulling at it.
98
Rep. gr.19 - Cooling
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
NOTICE
Risk of damage to material shaft of radiator roller blind.
– Only pull or push on outside of radiator roller blind frame.
– Press on outside of frame to press radiator roller blind -1-
into fastener.
– Fit air ducts -1- and -2- on radiator and engage them with
each other -arrows-.
– Check that lower fastener -3- is seated securely.
– Fit radiator cowl on radiator and engage.
– Install radiator module ⇒ Rep. gr. 19; Removing and instal‐
ling radiator module.
If control motor for radiator roller blind -V711- was removed and
installed:
– Perform control motor for radiator roller blind adaption func‐
tion using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access
to diagnoses.
4. Radiator, radiator fan
99
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
If control motor for radiator roller blind -V711- was renewed:
– Perform control motor for radiator roller blind renewal func‐
tion using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access
to diagnoses.
4.5
Removing and installing radiator cowl
with radiator fans
Removing
– Move impact bar into service position ⇒ General body re‐
pairs, exterior; Rep. gr. 63; Bumper (front); Moving impact
bar into service position and resetting.
CAUTION
Risk of injury as the radiator fan(s) may start up automatically.
– When working in the vicinity of the radiator, keep a safe
distance from the radiator fan.
– Do not reach into the radiator fan when unplugging the
electrical connector.
– Unplug electrical connector for radiator fan -VX57- -arrow-.
For clarity, the radiator module is removed in the following illus‐
trations.
– Press in retaining tabs -1- for radiator cowl -2- on both sides
in direction of -arrow A-.
100
Rep. gr.19 - Cooling
2024 VW ID.4 Owner's Manual
