ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
3
Removing and installing rear motor
Exploded view - motor (rear)
3.1
30
Rep. gr.10 - Removing and installing engine
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
1 - High voltage connector for
power and control electronics
for electric drive - JX1-
2 - Cable guide for high-volt‐
age wire
3 - Bolt for cable guide
❑ 6x
❑ 8 Nm
4 - O-ring
5 - Retaining clip
6 - Coolant hose
7 - Clip
8 - Hose clip
9 - Bolt for coolant connection
❑ 2x
❑ Renew after removing
❑ 8 Nm +90°
10 - O-ring
❑ Renew after removing
11 - Coolant connection
12 - Three-phase current
drive - VX54-
❑ With power and control
electronics for electric
drive - JX1-
❑ ⇒ Rep. gr. 93; Remov‐
ing and installing power
and control electronics
for electric drive, rear-
wheel drive
❑ ⇒ Rep. gr. 10; Removing rear motor
❑ ⇒ Rep. gr. 10; Installing rear motor
13 - Coolant pipe
❑ Remove high-voltage battery to remove ⇒ Rep. gr. 93; High-voltage battery unit
14 - O-ring for bleeder valve
15 - Bleeder valve
❑ Special lubricant for seal seat ⇒ Electronic parts catalogue (ETKA)
❑ Renew after removing
16 - Bolt for motor mounting
❑ 2x
❑ Renew after removing
❑ 130 Nm +180°
17 - Bolt for motor support
❑ 3x
❑ Renew after removing
❑ 70 Nm +180°
18 - Motor support
19 - Bolt for gearbox mounting
3. Removing and installing rear motor
31
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
❑ Renew after removing
❑ 130 Nm +180°
20 - Temperature sensor - G18-
❑ ⇒ Rep. gr. 19; Removing and installing temperature sensor [G18]
21 - O-ring
❑ Renew after removing
22 - Coolant hose
23 - Bracket
❑ Connection point for potential equalisation line
24 - Nut
❑ 8 Nm
25 - O-ring
26 - Breather line for gearbox
27 - Bolt for potential equalisation line
❑ 8 Nm
28 - Electrical connector for power and control electronics for electric drive - JX1-
3.2
Removing rear motor
Special tools and workshop equipment required
♦ Hook -3282/49-
♦ Pin -3282/48-
♦ bit XZN 16 -T10198-
♦ engine and gearbox jack -VAS 6931-
♦ engine bung set -VAS 6122-
♦ gearbox support -3282-
The three-phase current drive -VX54- along with the power and
control electronics for electric drive -JX1- will henceforth be
referred to as “motor”.
Removing
DANGER
High voltage can cause fatal injury.
Danger of severe or fatal injuries from electric shock or elec‐
tric arcs.
– Have a high-voltage technician (HVT) or a high-voltage
expert (HVE) de-energise the high-voltage system.
– ⇒ Rep. gr. 93; De-energising high-voltage system.
– Remove rear centre underbody cladding -1- ⇒ General body
repairs, exterior; Rep. gr. 66; Underbody cladding; Remov‐
ing and installing rear centre underbody cladding.
32
Rep. gr.10 - Removing and installing engine
2024 VW ID.4 Owner's Manual
