ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
Bolts
Tightening torque/angle speci‐
fication
Engine bracket -VAS 6095A/ 80 Nm
1-22- to retaining plate -
VW309A-
2.4
Installing front motor
2.4.1
Installing front motor, left-hand drive
vehicles
Special tools and workshop equipment required
♦ lifting tackle -VAS 501 021-
♦ workshop hoist -VAS 6100-
The three-phase current drive 2 -VX97- along with the power
and control electronics 2 for electric drive -JX4- will henceforth
be referred to as “motor”.
Installing
– Insert bracket of lifting tackle -VAS 501 021--A- into holes
-arrows B-.
– Screw bolt -1- to stop into hole -arrow C- by hand.
– Secure shackle -2- in centre hole.
– Attach workshop hoist -VAS 6100- to shackle -2-.
– Use workshop hoist to position motor -1- on subframe.
2. Removing and installing front motor
25
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
– Align motor support with gearbox mounting, and screw in
bolts -3- and -4- until stop.
– Tighten bolt -2-.
– Tighten bolts -3- and -4-.
– Detach lifting tackle -VAS 501 021- -arrow-.
Important
•
Further installation is carried out in reverse order of removal,
observing the following:
– Install subframe together with motor ⇒ Running gear, axles,
steering; Rep. gr. 40; Subframe; Removing and installing
subframe with motor.
Tightening torques
♦ ⇒ Rep. gr. 10; Assembly overview – front motor
2.4.2
Installing front motor, right-hand drive
vehicles
Special tools and workshop equipment required
♦ lifting tackle -VAS 501 021-
♦ workshop hoist -VAS 6100-
The three-phase current drive 2 -VX97- along with the power
and control electronics 2 for electric drive -JX4- will henceforth
be referred to as “motor”.
Installing
– Insert bracket of lifting tackle -VAS 501 021--A- into holes
-arrows B-.
26
Rep. gr.10 - Removing and installing engine
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
– Screw bolt -1- to stop into hole -arrow C- by hand.
– Secure shackle -2- in centre hole.
– Attach workshop hoist -VAS 6100- to shackle -2-.
– Use workshop hoist to position motor -1- on subframe in
such a way that a distance of -a- = 20 mm remains between
motor support and gearbox mounting.
– Align motor support with gearbox mounting, and screw in
bolts -2- and -3- until bolt heads make contact with gearbox
mounting.
– Detach lifting tackle -VAS 501 021- -arrow-.
– Use assembly lever -A- to slightly raise motor -1- in direction
of -arrow B- and push it against gearbox mountings in direc‐
tion of -arrow C-.
2. Removing and installing front motor
27
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
– Screw in bolts -1- and -2- entirely -a-, and tighten them.
– Tighten bolt -1- for motor mounting -2-.
Important
•
Further installation is carried out in reverse order of removal,
observing the following:
28
Rep. gr.10 - Removing and installing engine
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
– Install subframe together with motor ⇒ Running gear, axles,
steering; Rep. gr. 40; Subframe; Removing and installing
subframe with motor.
Tightening torques
♦ ⇒ Rep. gr. 10; Assembly overview – front motor
2. Removing and installing front motor
29
2024 VW ID.4 Owner's Manual
