ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
Tightening torques
Bolts
Specified torque/turning fur‐
ther angle
Bracket -VAS 501 019/1- and 25 Nm
bracket -VAS 501 019/2- to lift‐
ing tackle -VAS 501 019-
Adapter for engine and gear‐ 80 Nm
box support -VAS 6095A/1-21-
on retaining plate -VW309A-
Adapter for engine and gear‐ 20 Nm
box support -VAS 6095A/1-21-
to motor
3.4
Installing rear motor
Special tools and workshop equipment required
♦ bit XZN 16 -T10198-
♦ engine and gearbox jack -VAS 6931-
♦ gearbox support -3282-
The three-phase current drive -VX54- along with the power and
control electronics for electric drive -JX1- will henceforth be
referred to as “motor”.
Installing
Important
•
Motor and gearbox secured to gearbox support -3282- and
engine and gearbox jack -VAS 6931-.
– Raise motor with gearbox -1- up to 150 mm before installa‐
tion position.
40
Rep. gr.10 - Removing and installing engine
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
– Fit high-voltage connector -1- above gearbox, and close
locking bracket in direction of -arrow A-.
– Tighten bolts -2- and -3-.
– Fit coolant hose -1- above gearbox, and close locking ele‐
ment -2-. Ensure proper engagement by pulling.
– Fit gearbox breather line -3- onto gearbox.
3. Removing and installing rear motor
41
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
– Close retaining clips -arrow A- and -arrow B-.
– Raise motor with gearbox -1- until bolts for motor and gear‐
box mountings can be started.
– Use bit XZN 16 -T10198- to tighten bolts for motor and gear‐
box mounting.
– Mount bracket -1- for potential equalisation line on gearbox
and tighten nut -arrow-.
– Install left and right drive shaft ⇒ Running gear, axles, steer‐
ing; Rep. gr. 42; Drive shaft; Removing and installing drive
shaft.
Further installation is carried out in reverse order of removal,
observing the following:
WARNING
High voltage can cause fatal injury.
Danger of severe or fatal injuries from electric shock or elec‐
tric arcs.
– Have a high-voltage technician (HVT) or a high-voltage
expert (HVE) re-energise the high-voltage system.
– ⇒ Rep. gr. 93; Re-energise high-voltage system.
– If the three-phase current drive -VX54- or the power and
control electronics for electric drive -JX1- have been re‐
newed, perform calibration ⇒ Rep. gr. 93; Calibrating three-
phase current drive [VX54-.
42
Rep. gr.10 - Removing and installing engine
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
Tightening torques
♦ ⇒ Rep. gr. 10; Exploded view - motor (rear)
♦ ⇒ Rep. gr. 93; Assembly overview – electric drive motor
♦ ⇒ Rep. gr. 93; Assembly overview – charging unit for high-
voltage battery, rear-wheel drive
♦ ⇒ Running gear, axles, steering; Rep. gr. 42; Drive shaft;
Assembly overview - drive shaft
♦ ⇒ General body repairs, exterior; Rep. gr. 66; Underbody
cladding; Assembly overview – underbody cladding
3. Removing and installing rear motor
43
2024 VW ID.4 Owner's Manual
