ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
5.15
Removing and installing connecting el‐
ement, 48, 55 kWh
5.15.1
Removing and installing connecting el‐
ement
Special tools and workshop equipment required
♦ High-voltage tool set -VAS 6762-
♦ Torque wrench -VAS 6883/1A-
♦ accidental contact protection -T10608-
♦ accidental contact protection insert -T10628-
DANGER
Danger to life from high voltage.
Electric shocks or arcs may lead to serious injuries or death.
– Suitable personal protective equipment (PPE) must be
worn for the subsequent work steps.
– The subsequent work steps must be supervised by an
additional specialist with appropriate qualification.
– Outside the hazard area, the additional authorised special‐
ist can support the HVE as required within the scope of his
or her qualification.
Put on the required protective equipment for the subsequent
work steps:
♦ Arc flash resistant clothing (at least APC 2, at least 318 kJ)
♦ Helmet with arc flash resistant visor (at least APC 2, at least
318 kJ)
♦ Arc flash resistant gloves with nitrile glove liners (at least
APC 2, at least 318 kJ), insulating up to at least 500 V
♦ Safety shoes with ESD protection
The switching unit for high-voltage battery, negative terminal
-SX7- will henceforth be referred to as “switching unit, negative
terminal”.
Removing
– ⇒ Rep. gr. 93; Opening high-voltage battery 1 [AX2].
– ⇒ Rep. gr. 93; Opening electrical circuit, 48, 55 kWh.
– Fit accidental contact protection insert -T10628- onto battery
module 1 -J991-.
186
Rep. gr.93 - Electric drive systems
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
– Unscrew bolts -2- from high-voltage connector -1- on switch‐
ing unit, negative terminal -3- and battery module 1 -J991-.
– Remove high-voltage connector -1-.
– Fit accidental contact protection -T10608- onto exposed
high-voltage connection on battery module 1 -J991-.
– Detach cap for switching unit, negative terminal -3-.
– Unscrew bolts -2-.
– Unscrew bolts -3-.
– Remove connecting element -1-.
Installing
Install in reverse order of removal, observing the following:
– Check seal for damage.
– Keep sealing surface free of dust and grease. Clean with
cleaning solution ⇒ Electronic parts catalogue (ETKA).
– Apply sealant all around on outer side of connecting ele‐
ment, next to existing seal. Sealant ⇒ Electronic parts cata‐
logue (ETKA).
– When installing, pay attention to equal tolerance between
connecting element and lower part of battery housing. Seal
must come fully into contact with lower part of battery hous‐
ing.
– After installation of a high-voltage connector, measurements
must be performed to make sure there is no risk of a short-
circuit to the lower part of battery housing.
– Have all torque settings checked by a 2nd mechanic.
Tightening torques
♦ ⇒ Rep. gr. 93; Assembly overview – switching unit for high-
voltage battery, 48, 55, 62 kWh
♦ ⇒ Rep. gr. 93; Assembly overview – high-voltage battery,
connecting element, 48, 55, 62 kWh
5. High-voltage battery components
187
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
5.16
Removing and installing connecting el‐
ement, 62 kWh
5.16.1
Removing and installing connecting el‐
ement
Special tools and workshop equipment required
♦ High-voltage tool set -VAS 6762-
♦ Torque wrench -VAS 6883/1A-
♦ accidental contact protection -T10608-
♦ accidental contact protection insert -T10628-
DANGER
Danger to life from high voltage.
Electric shocks or arcs may lead to serious injuries or death.
– Suitable personal protective equipment (PPE) must be
worn for the subsequent work steps.
– The subsequent work steps must be supervised by an
additional specialist with appropriate qualification.
– Outside the hazard area, the additional authorised special‐
ist can support the HVE as required within the scope of his
or her qualification.
Put on the required protective equipment for the subsequent
work steps:
♦ Arc flash resistant clothing (at least APC 2, at least 318 kJ)
♦ Helmet with arc flash resistant visor (at least APC 2, at least
318 kJ)
♦ Arc flash resistant gloves with nitrile glove liners (at least
APC 2, at least 318 kJ), insulating up to at least 500 V
♦ Safety shoes with ESD protection
The switching unit for high-voltage battery, negative terminal
-SX7- will henceforth be referred to as “switching unit, negative
terminal”.
Removing
– ⇒ Rep. gr. 93; Opening high-voltage battery 1 [AX2].
– ⇒ Rep. gr. 93; Opening electrical circuit, 48, 55 kWh.
– Fit accidental contact protection insert -T10628- onto battery
module 1 -J991-.
188
Rep. gr.93 - Electric drive systems
2024 VW ID.4 Owner's Manual
