ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
– Make sure that sender -A- is properly seated on dowel pin
-arrow-.
– Insert bolts -1- and -2-.
– First tighten bolts -1- and then bolts -2-.
– Install power and control electronics for electric drive - JX1-
⇒ Rep. gr. 93; Removing and installing power and control
electronics for electric drive, rear-wheel drive.
Tightening torques
♦ ⇒ Rep. gr. 93; Assembly overview – electric drive motor
7.5
Removing and installing drive motor ro‐
tor position sender, all-wheel drive
7.5.1
Removing and installing drive motor ro‐
tor position sender 1 [G713]
The drive motor rotor position sender 1 -G713- will henceforth
be referred to as “sender”.
Note
Bolts could fall into the motor. Turn the motor to horizontal
position.
238
Rep. gr.93 - Electric drive systems
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
Removing
– Remove power and control electronics for electric drive -
JX1- ⇒ Rep. gr. 93; Removing and installing power and con‐
trol electronics for electric drive, rear-wheel drive.
– Unscrew bolts -arrows- for sender -A-.
– Pull sender -A- off connection -2- -arrow-.
Installing
– Fit sender -A- onto connection -2- -arrow-.
– Make sure that sender -A- is properly seated on dowel pin
-arrow-.
7. Electric drive motor
239
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
– Insert bolts -1- and -2-.
– First tighten bolts -1- and then bolts -2-.
– Install power and control electronics for electric drive - JX1-
⇒ Rep. gr. 93; Removing and installing power and control
electronics for electric drive, rear-wheel drive.
Tightening torques
♦ ⇒ Rep. gr. 93; Assembly overview – electric drive motor
7.5.2
Removing and installing rotor position
sender 1 for drive motor 2 [G1147]
The rotor position sender 1 for drive motor 2 -G1147- will
henceforth be referred to as “sender”.
Removing
– ⇒ Rep. gr. 10; Removing front motor.
– ⇒ Rep. gr. 10; Securing motor (front) to engine and gearbox
support.
– Unscrew bolts -arrows- for bearing plate -1-.
240
Rep. gr.93 - Electric drive systems
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
– Pull bearing plate together with shaft out of motor.
– Pull electrical connectors -2- off sender -1-.
– Unscrew bolts -arrows-, and detach sender -1-.
Installing
– Insert sender -1-, and tighten bolts -arrows-.
– Make sure that the seal -arrow- has been properly inserted
at the electrical connector.
7. Electric drive motor
241
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
– Connect electrical connectors -2-. Check for proper engage‐
ment by pulling.
– Thoroughly clean sealing surfaces on bearing plate and mo‐
tor.
– Insert bearing plate with shaft and new seal into motor.
– Tighten bolts -arrows- for bearing plate.
242
Rep. gr.93 - Electric drive systems
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
Tightening torques
♦ ⇒ Rep. gr. 93; Assembly overview – electric drive motor
7. Electric drive motor
243
2024 VW ID.4 Owner's Manual
