ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
16 - Bolt for motor support
❑ Qty. 2
❑ Renew after removing
❑ 50 Nm +90°
17 - Front motor mounting
❑ ⇒ Running gear, axles, steering; Rep. gr. 40; Subframe; Renewing front motor mounting
18 - Bolt for front motor mounting
❑ Renew after removing
❑ 130 Nm +180°
19 - Bolt for motor support
❑ Qty. 2
❑ Renew after removing
❑ 50 Nm +90°
20 - Bolt for front motor mounting
❑ Renew after removing
❑ 130 Nm +180°
21 - Front motor mounting
❑ ⇒ Running gear, axles, steering; Rep. gr. 40; Subframe; Renewing front motor mounting
22 - Motor support
2.2
Removing front motor
2.2.1
Removing front motor, left-hand drive
vehicles
Special tools and workshop equipment required
♦ engine bung set -VAS 6122-
♦ lifting tackle -VAS 501 021-
♦ workshop hoist -VAS 6100-
The three-phase current drive 2 -VX97- along with the power
and control electronics 2 for electric drive -JX4- will henceforth
be referred to as “motor”.
Removing
Once the drive shafts have been removed, seal the drive shaft
flange using sealing plugs from engine bung set -VAS 6122-.
Important
•
There must be no gear oil running out.
– Remove subframe together with motor ⇒ Running gear,
axles, steering; Rep. gr. 40; Subframe; Removing and instal‐
ling subframe with motor.
– Insert bracket of lifting tackle -VAS 501 021--A- into holes
-arrows B-.
2. Removing and installing front motor
19
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
– Screw bolt -1- to stop into hole -arrow C- by hand.
– Secure shackle -2- in centre hole.
– Attach workshop hoist -VAS 6100- to shackle -arrow-.
– Use workshop hoist to take up weight of motor -1-.
– Unscrew bolts -2-, -3- and -4-.
– Use workshop hoist to raise motor -1-.
♦ ⇒ Rep. gr. 10; Securing motor (front) to engine and gearbox
support
2.2.2
Removing front motor, right-hand drive
vehicles
Special tools and workshop equipment required
♦ engine bung set -VAS 6122-
♦ lifting tackle -VAS 501 021-
♦ workshop hoist -VAS 6100-
20
Rep. gr.10 - Removing and installing engine
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
The three-phase current drive 2 -VX97- along with the power
and control electronics 2 for electric drive -JX4- will henceforth
be referred to as “motor”.
Removing
Once the drive shafts have been removed, seal the drive shaft
flange using sealing plugs from engine bung set -VAS 6122-.
Important
•
There must be no gear oil running out.
– Remove subframe together with motor ⇒ Running gear,
axles, steering; Rep. gr. 40; Subframe; Removing and instal‐
ling subframe with motor.
– Loosen bolts -1- and -2-, and unscrew them by 20 mm -a-.
– Unscrew bolt -1- for motor mounting -2-.
– Use assembly lever -A- to slightly raise motor -1- in direction
of -arrow B- and pull it towards rear in direction of -arrow C-.
2. Removing and installing front motor
21
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
– Insert bracket of lifting tackle -VAS 501 021--A- into holes
-arrows B-.
– Screw bolt -1- to stop into hole -arrow C- by hand.
– Secure shackle -2- in centre hole.
– Attach workshop hoist -VAS 6100- to shackle -arrow-.
– Use workshop hoist to take up weight of motor -1-.
22
Rep. gr.10 - Removing and installing engine
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
– Unscrew bolts -2- and -3-.
– Use workshop hoist to raise motor -1-.
♦ ⇒ Rep. gr. 10; Securing motor (front) to engine and gearbox
support
2.3
Securing motor (front) to engine and
gearbox support
Special tools and workshop equipment required
♦ Engine bracket -VAS 6095A/1-22-
♦ engine and gearbox support -VAS 6095A-
♦ engine bracket -VAS 6095A/1-22-
♦ lifting device -VAS 501 021-
♦ retaining plate -VW309A-
♦ workshop hoist -VAS 6100-
Three-phase current drive 2 -VX97- with power and control
electronics 2 for electric drive -JX4- are referred to as the motor
below.
– Insert bracket of lifting device -VAS 501 021- -A- in holes
-arrows B-.
– Screw bolt -1- hand-tight into hole -arrow C- as far as stop.
– Secure shackle -2- in centre hole.
– Attach workshop hoist -VAS 6100- to shackle -2- and raise
motor.
– Remove bolts -arrows- and detach motor support -1-.
2. Removing and installing front motor
23
2024 VW ID.4 Owner's Manual
