ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
– Lift catch -2- and pull off coolant hose.
– Unclip gearbox breather line -3- -arrow B-, and pull it off
gearbox.
NOTICE
Risk of damage to lines and hoses when lowering the mo‐
tor/gearbox assembly.
– Make sure that all connections between the motor/gearbox
and the vehicle body have been disconnected.
– When lowering, carefully guide motor/gearbox assembly
out of motor compartment.
– Lower motor with gearbox.
– Seal any open connections on motor and gearbox with plugs
from engine bung set -VAS 6122-.
3.3
Securing motor to engine and gearbox
support, rear motor
Special tools and workshop equipment required
♦ Adapter for engine and gearbox support -VAS 6095A/1-21-
♦ adapter for engine and gearbox support -VAS 6095A/1-21-
♦ engine and gearbox support -VAS 6095A-
♦ lifting tackle -VAS 501 019-
♦ retaining plate -VW309A-
♦ support plate -VW309A-
♦ workshop hoist -VAS 6100-
CAUTION
Risk of injury due to moving parts.
Danger of trapping or crushing parts of the body
– Never reach into or enter a danger zone.
Assemble lifting tackle -VAS 501 019--A-.
3. Removing and installing rear motor
37
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
– Fit bracket -VAS 501 019/1- -1- and bracket -VAS 501
019/2- -2- to lifting tackle as shown in illustration, and screw
in bolts -5-.
– Secure shackle -4- in hole shown in illustration.
– Align brackets -1- and -2- so that markings -arrows- align.
– Tighten bracket bolts -5-.
– Insert bracket -1- and bracket -2- of lifting tackle -A- into
holes -arrow B-.
38
Rep. gr.10 - Removing and installing engine
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
– Screw bolt -3- to stop into hole -arrow C- by hand.
– Attach workshop hoist -VAS 6100- to shackle -4-, and raise
motor.
– Fit adapter for engine and gearbox support -VAS 6095A/
1-21--A- to support plate -VW309A--B-, and tighten bolts.
– Fit adapter for engine and gearbox support -A- to motor -1-,
and tighten bolts.
– Secure motor -1- with adapter for engine and gearbox sup‐
port -A- and support plate -B- to engine and gearbox support
-VAS 6095A--C-.
3. Removing and installing rear motor
39
ID.4 2021 ➤, ID.3 2020 ➤
Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220 - Edition 11.2021
Tightening torques
Bolts
Specified torque/turning fur‐
ther angle
Bracket -VAS 501 019/1- and 25 Nm
bracket -VAS 501 019/2- to lift‐
ing tackle -VAS 501 019-
Adapter for engine and gear‐ 80 Nm
box support -VAS 6095A/1-21-
on retaining plate -VW309A-
Adapter for engine and gear‐ 20 Nm
box support -VAS 6095A/1-21-
to motor
3.4
Installing rear motor
Special tools and workshop equipment required
♦ bit XZN 16 -T10198-
♦ engine and gearbox jack -VAS 6931-
♦ gearbox support -3282-
The three-phase current drive -VX54- along with the power and
control electronics for electric drive -JX1- will henceforth be
referred to as “motor”.
Installing
Important
•
Motor and gearbox secured to gearbox support -3282- and
engine and gearbox jack -VAS 6931-.
– Raise motor with gearbox -1- up to 150 mm before installa‐
tion position.
40
Rep. gr.10 - Removing and installing engine
2024 VW ID.4 Owner's Manual
