ID.4 2021 ➤
Brake system - Edition 07.2021
– Fit clamping washer onto pivot pin.
– Continue installation in reverse order of removal.
5.4.2
Removing and installing brake pedal,
right-hand drive vehicles
Removing
– ⇒ Rep. gr. 46; Separate brake pedal from brake servo .
– Unscrew nut -2- from pivot pin -1- .
– Pull out pivot pin -1- towards left side in direction of -arrow- .
– Remove brake pedal from mounting bracket.
Installing
– Renew pivot pin and nut.
Important
•
Do not lubricate or grease the pivot pin. The pivot pin must
remain dry.
– Push pivot pin from left side to right side through mounting
bracket and brake pedal.
– Screw nut onto pivot pin, and tighten it.
– Continue installation in reverse order of removal.
Tightening torques
♦ ⇒ Rep. gr. 46; Assembly overview – brake pedal
5.5
Removing and installing mounting
bracket
5.5.1
Removing and installing mounting
bracket, left-hand drive vehicles
Installing
– Remove dash panel cover on front passenger side ⇒ Gener‐
al body repairs, interior; Rep. gr. 68; Compartments/covers;
Removing and installing dash panel cover on front passen‐
ger side .
– Remove footwell vent on driver side ⇒ Heating, air condition‐
ing system; Rep. gr. 87; Air duct; Removing and installing
footwell vent on driver side .
62
Rep. gr.46 - Brakes - mechanism
ID.4 2021 ➤
Brake system - Edition 07.2021
– Remove crash bar ⇒ General body repairs, interior; Rep.
gr. 70; Central tube for dash panel; Removing and installing
crash bar .
– Remove centre console ⇒ General body repairs, interior;
Rep. gr. 68; Centre console; Removing and installing centre
console .
– Remove tunnel support cover ⇒ General body repairs, interi‐
or; Rep. gr. 70; Dash panel; Removing and installing tunnel
support cover .
– Remove sill panel moulding at front. ⇒ General body repairs,
interior; Rep. gr. 70; Trims, interior; Removing and installing
sill panel moulding at front
– Remove lower A-pillar trim ⇒ General body repairs, interior;
Rep. gr. 70; Trims, interior; Removing and installing lower
A-pillar trim .
– ⇒ Rep. gr. 46; Separate brake pedal from brake servo .
– Disconnect electrical connector -4- from accelerator pedal
module -GX2- -1- .
– Pull floor covering -1- as far as possible towards rear.
– Remove filler piece -2- to gain access to mounting bracket
nut located behind it -3- .
– Unscrew nuts -1- to -5- .
5. Brake pedal
63
ID.4 2021 ➤
Brake system - Edition 07.2021
– Remove mounting bracket.
If mounting bracket is to be renewed:
– Separate accelerator pedal module -GX2- from mounting
bracket ⇒ Electric rear-wheel drive EIP220 and all-wheel
drive EIA200, EIP220; Rep. gr. 93; Accelerator mechanism;
Removing and installing accelerator pedal module [GX2] .
All vehicles (continued)
Installing
Install in reverse order of removal, observing the following:
– Tighten nuts in sequence -1- through -5- .
– ⇒ Rep. gr. 46; Connect brake pedal to brake servo .
Tightening torques
♦ ⇒ Rep. gr. 46; Assembly overview – brake pedal
♦ ⇒ Running gear, axles, steering; Rep. gr. 48; Steering col‐
umn; Assembly overview – steering column
64
Rep. gr.46 - Brakes - mechanism
ID.4 2021 ➤
Brake system - Edition 07.2021
♦ ⇒ Heating, air conditioning system; Rep. gr. 87; Air duct; As‐
sembly overview – air duct and air distribution in passenger
compartment
5.5.2
Removing and installing mounting
bracket, right-hand drive vehicles
Removing
– ⇒ General body repairs, interior; Rep. gr. 68; Compart‐
ments/covers; Removing and installing dash panel trim on
driver side
– ⇒ Heating, air conditioning system; Rep. gr. 87; Air duct;
Removing and installing footwell vent on driver side
– ⇒ General body repairs, interior; Rep. gr. 70; Central tube for
dash panel; Removing and installing crash bar
– Disconnect electrical connector from accelerator pedal mod‐
ule -GX2- .
– ⇒ Rep. gr. 46; Removing and installing brake pedal, right-
hand drive vehicles
– Unscrew nuts -1- to -5- .
– Remove mounting bracket.
If mounting bracket is to be renewed:
– Separate accelerator pedal module -GX2- from mounting
bracket ⇒ Electric rear-wheel drive EIP220 and all-wheel
drive EIA200, EIP220; Rep. gr. 93; Accelerator mechanism;
Removing and installing accelerator pedal module [GX2] .
All vehicles (continued)
Installing
Install in reverse order of removal, observing the following:
– Tighten nuts in sequence -1- through -5- .
5. Brake pedal
65
ID.4 2021 ➤
Brake system - Edition 07.2021
– ⇒ Rep. gr. 46; Connect brake pedal to brake servo .
Tightening torques
♦ ⇒ Rep. gr. 46; Assembly overview – brake pedal
♦ ⇒ Running gear, axles, steering; Rep. gr. 48; Steering col‐
umn; Assembly overview – steering column
♦ ⇒ Heating, air conditioning system; Rep. gr. 87; Air duct; As‐
sembly overview – air duct and air distribution in passenger
compartment
66
Rep. gr.46 - Brakes - mechanism
2024 VW ID.4 Owner's Manual
