Table of Contents > 3 Refrigerant circuit > 3.18 Removing and installing refrigerant pressure and temperature sender 2 [G826]

VW ID.4 Heating & Air Conditioning System ➜ 3.18 Removing and installing refrigerant pressure and temperature sender 2 [G826]

ID.4 2021 ➤  
Heating, air conditioning system - Edition 09.2021  
CAUTION  
Risk of frostbite from escaping pressurised refrigerant  
Risk of frostbite on skin and other parts of the body  
– Put on protective gloves.  
– Put on safety goggles.  
– Extract/drain refrigerant and then immediately open up re‐  
frigerant circuit.  
– Extract/drain refrigerant again if more than 10 minutes  
have passed since initial extraction and refrigerant circuit  
has not been opened up. Renewed evaporation has cre‐  
ated pressure in the refrigerant circuit.  
– Remove valve core -2- using socket -T10364/5-.  
Installing  
Installation is carried out in reverse order; note the following:  
– Perform function “Opening electrically actuated valves in re‐  
frigerant circuit for extracting, evacuating and charging” with  
⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Starting diagnosis.  
– ⇒ Air conditioners with refrigerant R744 - General informa‐  
tion; Rep. gr. 87; Working with the air conditioner service  
station; Charging refrigerant circuit  
Tightening torques  
♦ ⇒ Rep. gr. 87; Exploded view - refrigerant lines  
3.18  
Removing and installing refrigerant  
pressure and temperature sender 2  
[G826]  
3.18.1  
Removing and installing refrigerant  
pressure and temperature sender 2  
[G826]  
Special tools and workshop equipment required  
♦ engine bung set -VAS 6122-  
38  
Rep. gr.87 - Air conditioning system  
ID.4 2021 ➤  
Heating, air conditioning system - Edition 09.2021  
♦ socket -T40284-  
Removing  
Immediately seal any open lines and connections with clean  
plugs from engine bung set -VAS 6122-.  
– Carry out function “Open electrically actuated valves to  
drain, evacuate or charge refrigerant circuit” using ⇒ Vehicle  
diagnostic tester ⇒ Rep. gr. 00; Access to diagnoses.  
– ⇒ Air conditioning systems with refrigerant R744 – General  
notes; Rep. gr. 87; Working with air conditioner service sta‐  
tion; Draining refrigerant circuit.  
– Remove lock carrier ⇒ General body repairs, exterior; Rep.  
gr. 50; Lock carrier; Removing and installing lock carrier.  
– Detach coolant expansion tank, and lay it slightly aside  
⇒ Rep. gr. 19; Cooling system/coolant; Removing and instal‐  
ling coolant expansion tank.  
CAUTION  
Risk of frostbite from escaping pressurised refrigerant  
Risk of frostbite on skin and other parts of the body  
– Put on protective gloves.  
– Put on safety goggles.  
– Extract/drain refrigerant and then immediately open up re‐  
frigerant circuit.  
– Extract/drain refrigerant again if more than 10 minutes  
have passed since initial extraction and refrigerant circuit  
has not been opened up. Renewed evaporation has cre‐  
ated pressure in the refrigerant circuit.  
– Unscrew bolts -1-.  
– Pull off and remove refrigerant line -2-.  
– Mark (to avoid interchanging) and disconnect electrical con‐  
nector -5-.  
3. Refrigerant circuit  
39  
ID.4 2021 ➤  
Heating, air conditioning system - Edition 09.2021  
– Check connection of refrigerant line -1- and refrigerant pres‐  
sure and temperature sender 2 -G826- -4- for soiling, and  
clean as necessary.  
– Unscrew sender -4- using socket -T40284- while counter‐  
holding at refrigerant line -1- with open-end spanner.  
Installing  
Install in reverse order of removal, observing the following:  
– Install seals and captive fasteners free of oil.  
– Make sure that refrigerant lines are seated correctly, and  
tighten refrigerant pressure and temperature sender 2 -  
G826- while counterholding with open-end spanner.  
– Carry out function “Open electrically actuated valves to  
drain, evacuate or charge refrigerant circuit” using ⇒ Vehicle  
diagnostic tester ⇒ Rep. gr. 00; Access to diagnoses.  
– ⇒ Air conditioning systems with refrigerant R744 – General  
notes; Rep. gr. 87; Working with air conditioner service sta‐  
tion; Charging refrigerant circuit.  
Tightening torques  
♦ ⇒ Rep. gr. 87; Assembly overview – refrigerant lines  
♦ ⇒ Rep. gr. 87; Assembly overview – valve unit of heat pump  
3.19  
Removing and installing refrigerant  
pressure and temperature sender 3  
[G827]  
3.19.1  
Removing and installing refrigerant  
pressure and temperature sender 3  
G827  
Special tools and workshop equipment required  
♦ engine bung set -VAS 6122-  
Removing  
Seal off open pipes/lines and connections immediately with  
clean plugs from engine bung set -VAS 6122-.  
– Perform function “Opening electrically actuated valves in re‐  
frigerant circuit for extracting, evacuating and charging” with  
⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Starting diagnosis.  
– ⇒ Air conditioners with refrigerant R744 - General informa‐  
tion; Rep. gr. 87; Working with the air conditioner service  
station; Discharging refrigerant circuit.  
40  
Rep. gr.87 - Air conditioning system  

Need help?

If after viewing the owner's manual or service manual you still have some unresolved questions about the car VW ID.4 you can write to us using the link below, describing your problem in detail, we try to answer all questions.


Ask your question on the page - Support!