ID.4 2021 ➤
Heating, air conditioning system - Edition 09.2021
6.5
Removing and installing control motor
for front right temperature flap [VX35]
6.5.1
Removing and installing control motor
for front right temperature flap [VX35],
left-hand drive vehicles
Removing
The front right temperature flap -VX35- with right temperature
flap control motor -V159- and potentiometer for right tempera‐
ture flap control motor -G221- will henceforth be referred to as
control motor.
Mark position of control motors and connectors prior to removal
to avoid interchanging control motors at reinstallation.
– Deactivate function “Stationary air conditioning” ⇒ Owner’s
manual.
– Remove footwell vent on front passenger side ⇒ Rep. gr. 87;
Removing and installing footwell vent on front passenger
side.
– Unscrew bolts -2-.
– Disconnect electrical connector -3-.
– Remove control motor -1-.
Installing
Install in reverse order of removal, observing the following:
– Check shaft -A- and mounting -B- of control motor -C-. They
should be correctly aligned so that they can be joined to‐
gether.
6. Control motors
117
ID.4 2021 ➤
Heating, air conditioning system - Edition 09.2021
– Route electrical wire so that it cannot come into contact with
any moving parts (e.g. actuating arm on control motor).
If control motor has been renewed or installed at different posi‐
tion:
– Carry out function “Adapt flap limit stops of control mo‐
tors”⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to
diagnoses.
Tightening torques
♦ ⇒ Rep. gr. 87; Assembly overview – front control motors
♦ ⇒ Rep. gr. 87; Assembly overview – air duct and air distribu‐
tion in passenger compartment
6.5.2
Removing and installing control motor
for front right temperature flap [VX35],
right-hand drive vehicles
Removing
The front right temperature flap -VX35- with right temperature
flap control motor -V159- and potentiometer for right tempera‐
ture flap control motor -G221- will henceforth be referred to as
control motor.
Mark position of control motors and connectors prior to removal
to avoid interchanging control motors at reinstallation.
– Deactivate function “Stationary air conditioning” ⇒ Owner’s
manual.
– Remove footwell cover on driver side ⇒ General body re‐
pairs, interior; Rep. gr. 68; Compartments/covers; Removing
and installing footwell cover on driver side.
– Detach electrical wire -3-.
– Disconnect electrical connector -4-.
– Unscrew bolts -2-.
– Remove control motor -1-.
Installing
Install in reverse order of removal, observing the following:
– Check shaft -A- and mounting -B- of control motor -C-. They
should be correctly aligned so that they can be joined to‐
gether.
118
Rep. gr.87 - Air conditioning system
ID.4 2021 ➤
Heating, air conditioning system - Edition 09.2021
– Route electrical wire so that it cannot come into contact with
any moving parts (e.g. actuating arm on control motor).
If control motor has been renewed or installed at different posi‐
tion:
– Carry out function “Adapt flap limit stops of control mo‐
tors”⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to
diagnoses.
Tightening torques
♦ ⇒ Rep. gr. 87; Assembly overview – front control motors
♦ ⇒ General body repairs, interior; Rep. gr. 68; Compart‐
ments/covers; Assembly overview – dash panel cover on
driver side
6.6
Removing and installing control motor
for defroster flap [VX47]
Removing
The defroster flap -VX47- with defroster flap control motor -
V107- and potentiometer for defroster flap control motor -G135-
will henceforth be referred to as control motor.
Mark position of control motors and connectors prior to removal
to avoid interchanging control motors at reinstallation.
– Deactivate function “Stationary air conditioning” ⇒ Owner’s
manual.
– Remove dash panel ⇒ General body repairs, interior; Rep.
gr. 70; Dash panel; Removing and installing dash panel.
– Unscrew bolts -2-.
– Disconnect electrical connector -3-.
– Remove control motor -1-.
6. Control motors
119
2024 VW ID.4 Owner's Manual
