ID.4 2021 ➤
Heating, air conditioning system - Edition 09.2021
Installing
Install in reverse order of removal, observing the following:
– Check shaft -A- and mounting -B- of control motor -C-. They
should be correctly aligned so that they can be joined to‐
gether.
– Route electrical wire so that it cannot come into contact with
any moving parts (e.g. actuating arm on control motor).
If control motor has been renewed or installed at different posi‐
tion:
– Carry out function “Adapt flap limit stops of control mo‐
tors”⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to
diagnoses.
Tightening torques
♦ ⇒ Rep. gr. 87; Assembly overview – front control motors
♦ ⇒ General body repairs, interior; Rep. gr. 70; Dash panel;
Assembly overview – dash panel
6.7
Removing and installing control motor
for front left air distribution flap [VX93]
6.7.1
Removing and installing control motor
for front left air distribution flap [VX93],
left-hand drive vehicles
Removing
The front left air distribution flap -VX93- with front left air dis‐
tribution flap control motor -V706- and potentiometer for front
left air distribution flap control motor -G1105- will henceforth be
referred to as “control motor”.
Mark position of control motors and connectors prior to removal
to avoid interchanging control motors at reinstallation.
– Deactivate function “Stationary air conditioning” ⇒ Owner’s
manual.
– Remove tunnel support cover ⇒ General body repairs, interi‐
or; Rep. gr. 70; Dash panel; Removing and installing tunnel
support cover.
– Remove footwell vent on driver side ⇒ Rep. gr. 87; Remov‐
ing and installing footwell vent on driver side.
– Lift control unit for head-up display -J898--3- approx. 35 mm
far enough to gain access to control motor bolts, and sup‐
port it there ⇒ Electrical system; Rep. gr. 90; Dash panel
120
Rep. gr.87 - Air conditioning system
ID.4 2021 ➤
Heating, air conditioning system - Edition 09.2021
insert; Removing and installing control unit for head-up dis‐
play [J898].
– Unscrew bolts -2-.
– Disconnect electrical connector -4-.
– Remove control motor -1-.
Installing
Install in reverse order of removal, observing the following:
– Check shaft -A- and mounting -B- of control motor -C-. They
should be correctly aligned so that they can be joined to‐
gether.
– Route electrical wire so that it cannot come into contact with
any moving parts (e.g. actuating arm on control motor).
If control motor has been renewed or installed at different posi‐
tion:
– Carry out function “Adapt flap limit stops of control mo‐
tors”⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to
diagnoses.
Tightening torques
♦ ⇒ Rep. gr. 87; Assembly overview – front control motors
♦ ⇒ Electrical system; Rep. gr. 90; Dash panel insert; Assem‐
bly overview – head-up display
6.7.2
Removing and installing control motor
for front left air distribution flap [VX93],
right-hand drive vehicles
Removing
The front left air distribution flap -VX93- with front left air dis‐
tribution flap control motor -V706- and potentiometer for front
6. Control motors
121
ID.4 2021 ➤
Heating, air conditioning system - Edition 09.2021
left air distribution flap control motor -G1105- will henceforth be
referred to as “control motor”.
Mark position of control motors and connectors prior to removal
to avoid interchanging control motors at reinstallation.
– Deactivate function “Stationary air conditioning” ⇒ Owner’s
manual.
– Remove bracket for control unit 1 for information electronics
[J794] ⇒ Communication; Rep. gr. 91; Components/control
units; Control unit 1 for information electronics [J794].
– Disconnect electrical connector -3-.
– Unscrew bolts -2-.
– Remove control motor -1-.
Installing
Install in reverse order of removal, observing the following:
– Check shaft -A- and mounting -B- of control motor -C-. They
should be correctly aligned so that they can be joined to‐
gether.
– Route electrical wire so that it cannot come into contact with
any moving parts (e.g. actuating arm on control motor).
If control motor has been renewed or installed at different posi‐
tion:
– Carry out function “Adapt flap limit stops of control mo‐
tors”⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to
diagnoses.
Tightening torques
♦ ⇒ Rep. gr. 87; Assembly overview – front control motors
122
Rep. gr.87 - Air conditioning system
ID.4 2021 ➤
Heating, air conditioning system - Edition 09.2021
6.8
Removing and installing control motor
for front right air distribution flap [VX94]
6.8.1
Removing and installing control mo‐
tor for front right air distribution flap
[VX94], left-hand drive vehicles
Removing
The front right air distribution flap -VX94- with right air distribu‐
tion flap control motor -V707- and potentiometer for front right
air distribution flap control motor -G1106- will henceforth be
referred to as control motor.
Mark position of control motors and connectors prior to removal
to avoid interchanging control motors at reinstallation.
– Deactivate function “Stationary air conditioning” ⇒ Owner’s
manual.
– Remove bracket for control unit 1 for information electronics
[J794] ⇒ Communication; Rep. gr. 91; Components/control
units; Control unit 1 for information electronics [J794].
– Disconnect electrical connector -3-.
– Unscrew bolts -2-.
– Remove control motor -1-.
Installing
Install in reverse order of removal, observing the following:
– Check shaft -A- and mounting -B- of control motor -C-. They
should be correctly aligned so that they can be joined to‐
gether.
6. Control motors
123
2024 VW ID.4 Owner's Manual
