ID.4 2021 ➤
Heating, air conditioning system - Edition 09.2021
6.8
Removing and installing control motor
for front right air distribution flap [VX94]
6.8.1
Removing and installing control mo‐
tor for front right air distribution flap
[VX94], left-hand drive vehicles
Removing
The front right air distribution flap -VX94- with right air distribu‐
tion flap control motor -V707- and potentiometer for front right
air distribution flap control motor -G1106- will henceforth be
referred to as control motor.
Mark position of control motors and connectors prior to removal
to avoid interchanging control motors at reinstallation.
– Deactivate function “Stationary air conditioning” ⇒ Owner’s
manual.
– Remove bracket for control unit 1 for information electronics
[J794] ⇒ Communication; Rep. gr. 91; Components/control
units; Control unit 1 for information electronics [J794].
– Disconnect electrical connector -3-.
– Unscrew bolts -2-.
– Remove control motor -1-.
Installing
Install in reverse order of removal, observing the following:
– Check shaft -A- and mounting -B- of control motor -C-. They
should be correctly aligned so that they can be joined to‐
gether.
6. Control motors
123
ID.4 2021 ➤
Heating, air conditioning system - Edition 09.2021
– Route electrical wire so that it cannot come into contact with
any moving parts (e.g. actuating arm on control motor).
If control motor has been renewed or installed at different posi‐
tion:
– Carry out function “Adapt flap limit stops of control mo‐
tors”⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to
diagnoses.
Tightening torques
♦ ⇒ Rep. gr. 87; Assembly overview – front control motors
6.8.2
Removing and installing control mo‐
tor for front right air distribution flap
[VX94], right-hand drive vehicles
Removing
The front right air distribution flap -VX94- with right air distribu‐
tion flap control motor -V707- and potentiometer for front right
air distribution flap control motor -G1106- will henceforth be
referred to as control motor.
Mark position of control motors and connectors prior to removal
to avoid interchanging control motors at reinstallation.
– Deactivate function “Stationary air conditioning” ⇒ Owner’s
manual.
– Remove footwell vent on driver side ⇒ Rep. gr. 87; Remov‐
ing and installing footwell vent on driver side.
– Disconnect electrical connector -3-.
– Unscrew bolts -2-.
– Remove control motor -1-.
Installing
Install in reverse order of removal, observing the following:
– Check shaft -A- and mounting -B- of control motor -C-. They
should be correctly aligned so that they can be joined to‐
gether.
124
Rep. gr.87 - Air conditioning system
ID.4 2021 ➤
Heating, air conditioning system - Edition 09.2021
– Route electrical wire so that it cannot come into contact with
any moving parts (e.g. actuating arm on control motor).
If control motor has been renewed or installed at different posi‐
tion:
– Carry out function “Adapt flap limit stops of control mo‐
tors”⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to
diagnoses.
Tightening torques
♦ ⇒ Rep. gr. 87; Assembly overview – front control motors
♦ ⇒ Rep. gr. 87; Assembly overview – air duct and air distribu‐
tion in passenger compartment
6.9
Removing and installing control motor
for rear temperature flap [VX95]
Removing
The rear temperature flap -VX95- with rear temperature flap
control motor -V137- and potentiometer for rear temperature
flap control motor -G479- will henceforth be referred to as con‐
trol motor.
Mark position of control motors and connectors prior to removal
to avoid interchanging control motors at reinstallation.
– Deactivate function “Stationary air conditioning” ⇒ Owner’s
manual.
– Remove tunnel support cover ⇒ General body repairs, interi‐
or; Rep. gr. 70; Dash panel; Removing and installing tunnel
support cover.
– Disconnect electrical connector -4-.
– Unscrew bolts -1- and -3-.
– Remove control motor -2-.
6. Control motors
125
2024 VW ID.4 Owner's Manual
