ID.4 2021 ➤
Heating, air conditioning system - Edition 09.2021
1 - Bolt
❑ 1.5 Nm
2 - Control motor for fresh
air and air recirculation flap -
VX96-
❑ ⇒ Rep. gr. 87; Remov‐
ing and installing con‐
trol motor for fresh
air and air recirculation
flap VX96
3 - Actuator
4 - Heater and air conditioning
unit
❑ ⇒ Rep. gr. 87; Remov‐
ing and installing heater
and air conditioning unit
6.4
Removing and installing control motor
for front left temperature flap [VX34]
6.4.1
Removing and installing control motor
for front left temperature flap [VX34],
LHD vehicles
Removing
The front left temperature flap -VX34- with left temperature flap
control motor -V158- and potentiometer for left temperature flap
control motor -G220- will henceforth be referred to as control
motor.
Mark position of control motors and connectors prior to removal
to avoid interchanging control motors at reinstallation.
– Deactivate function “Stationary air conditioning” ⇒ Owner’s
manual.
– Release mounting bracket ⇒ Brake system; Rep. gr. 46;
Brake pedal; Removing and installing mounting bracket.
– Disconnect electrical connector -3-.
114
Rep. gr.87 - Air conditioning system
ID.4 2021 ➤
Heating, air conditioning system - Edition 09.2021
– Unscrew bolts -2- and -4-.
– Remove control motor -1-.
Installing
Install in reverse order of removal, observing the following:
– Check shaft -A- and mounting -B- of control motor -C-. They
should be correctly aligned so that they can be joined to‐
gether.
– Route electrical wire so that it cannot come into contact with
any moving parts (e.g. actuating arm on control motor).
If control motor has been renewed or installed at different posi‐
tion:
– Carry out function “Adapt flap limit stops of control mo‐
tors”⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to
diagnoses.
Tightening torques
♦ ⇒ Rep. gr. 87; Assembly overview – front control motors
♦ ⇒ Brake system; Rep. gr. 46; Brake pedal; Assembly over‐
view – brake pedal
6.4.2
Removing and installing control motor
for front left temperature flap [VX34],
right-hand drive vehicles
Removing
The front left temperature flap -VX34- with left temperature flap
control motor -V158- and potentiometer for left temperature flap
control motor -G220- will henceforth be referred to as control
motor.
6. Control motors
115
ID.4 2021 ➤
Heating, air conditioning system - Edition 09.2021
Mark position of control motors and connectors prior to removal
to avoid interchanging control motors at reinstallation.
– Deactivate function “Stationary air conditioning” ⇒ Owner’s
manual.
– Remove footwell vent on front passenger side ⇒ Rep. gr. 87;
Removing and installing footwell vent on front passenger
side.
– Remove Fan for control unit -V274- ⇒ Electrical system;
Rep. gr. 97; Control units; Removing and installing fan for
control unit [V274].
– Disconnect electrical connector -3-.
– Unscrew bolts -2-.
– Remove control motor -1-.
Installing
Install in reverse order of removal, observing the following:
– Check shaft -A- and mounting -B- of control motor -C-. They
should be correctly aligned so that they can be joined to‐
gether.
– Route electrical wire so that it cannot come into contact with
any moving parts (e.g. actuating arm on control motor).
If control motor has been renewed or installed at different posi‐
tion:
– Carry out function “Adapt flap limit stops of control mo‐
tors”⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to
diagnoses.
Tightening torques
♦ ⇒ Rep. gr. 87; Assembly overview – front control motors
♦ ⇒ Rep. gr. 87; Assembly overview – air duct and air distribu‐
tion in passenger compartment
116
Rep. gr.87 - Air conditioning system
ID.4 2021 ➤
Heating, air conditioning system - Edition 09.2021
6.5
Removing and installing control motor
for front right temperature flap [VX35]
6.5.1
Removing and installing control motor
for front right temperature flap [VX35],
left-hand drive vehicles
Removing
The front right temperature flap -VX35- with right temperature
flap control motor -V159- and potentiometer for right tempera‐
ture flap control motor -G221- will henceforth be referred to as
control motor.
Mark position of control motors and connectors prior to removal
to avoid interchanging control motors at reinstallation.
– Deactivate function “Stationary air conditioning” ⇒ Owner’s
manual.
– Remove footwell vent on front passenger side ⇒ Rep. gr. 87;
Removing and installing footwell vent on front passenger
side.
– Unscrew bolts -2-.
– Disconnect electrical connector -3-.
– Remove control motor -1-.
Installing
Install in reverse order of removal, observing the following:
– Check shaft -A- and mounting -B- of control motor -C-. They
should be correctly aligned so that they can be joined to‐
gether.
6. Control motors
117
2024 VW ID.4 Owner's Manual
