ID.4 2021 ➤
General body repairs, exterior - Edition 05.2021
7
Exterior mirror
7.1
Assembly overview – exterior mirror
The overview is shown for the left side of vehicle as an exam‐
ple.
7. Exterior mirror
251
ID.4 2021 ➤
General body repairs, exterior - Edition 05.2021
1 - Mirror mounting
❑ With driver side exte‐
rior mirror -VX4- and
passenger side exterior
mirror -VX5-
❑ ⇒ Rep. gr. 66; Remov‐
ing and installing exteri‐
or mirror
2 - Driver side turn signal re‐
peater bulb -L131-/front pas‐
senger side turn signal re‐
peater bulb -L132-
❑ ⇒ Electrical system;
Rep. gr. 94; Lights in
exterior mirror; Remov‐
ing and installing turn
signal repeater bulb
[L131]/[L132]
3 - Upper mirror cover
❑ ⇒ Rep. gr. 66; Remov‐
ing and installing mirror
cover
4 - Lane change assist warn‐
ing lamp in left exterior mir‐
ror -K312-/lane change assist
warning lamp in right exterior
mirror -K311-
❑ Depending on equip‐
ment/version
❑ ⇒ Driver assist
systems; Rep.
gr. 98; Senders/sen‐
sors/control units; Re‐
moving and installing
lane change assist
warning lamp in exteri‐
or mirror [K311]/[K312]
5 - Bolt
❑ 20 Nm
6 - Cap
7 - Bolt
❑ 0.8 Nm
8 - Mirror adjustment unit
❑ Driver side with driver side mirror adjustment motor 2 -V17-, driver side mirror adjustment motor
-V149- and driver side fold-in mirror motor -V121-; optionally with potentiometer for horizontal adjust‐
ment of driver side mirror -G514- and potentiometer for vertical adjustment of driver side mirror -G515-
❑ Front passenger side with front passenger side mirror adjustment motor 2 -V25-, front passenger side
mirror adjustment motor -V150- and front passenger side fold-in mirror motor -V122-; optionally with
potentiometer for horizontal adjustment of front passenger side mirror -G516- und potentiometer for
vertical adjustment of front passenger mirror -G517-
❑ ⇒ Rep. gr. 66; Removing and installing mirror adjustment unit
9 - Bolt
❑ 0.8 Nm
10 - Mirror frame
❑ ⇒ Rep. gr. 66; Removing and installing mirror frame
11 - Bolt
252
Rep. gr.66 - Exterior equipment
ID.4 2021 ➤
General body repairs, exterior - Edition 05.2021
❑ qty. 2
❑ 0.8 Nm
12 - Mirror glass
❑ ⇒ Rep. gr. 66; Removing and installing mirror glass
13 - Lower mirror cover
❑ ⇒ Rep. gr. 66; Removing and installing mirror cover
14 - Left overhead view camera -R244-/right overhead view camera -R245-
❑ Depending on equipment/version
❑ ⇒ Driver assist systems; Rep. gr. 98; Senders/sensors/control units; Removing and installing left/right
overhead view camera [R244]/[R245]
15 - Bracket for overhead view camera
❑ Depending on equipment/version
16 - Bolt
❑ Depending on equipment/version
❑ qty. 2
❑ 0.8 Nm
17 - Entry light in exterior mirror, driver side -W52-/entry light in exterior mirror, front passenger side -W53-
❑ Depending on equipment/version
18 - Bolt
❑ Depending on equipment/version
❑ qty. 2
❑ 0.8 Nm
7.2
Removing and installing exterior mirror
Removal and installation are described for the left side of vehi‐
cle as an example.
Electrical wires and electrical connectors in a new exterior mir‐
ror are always prepared for the maximum equipment.
Electrical connectors that are not required must be secured to
prevent them from making noise.
Removing
– Remove front door trim ⇒ General body repairs, interior;
Rep. gr. 70; Front door trims; Removing and installing front
door trim.
– Disconnect electrical connectors -3-.
7. Exterior mirror
253
ID.4 2021 ➤
General body repairs, exterior - Edition 05.2021
– Lever off cap -4-.
– Unscrew bolt -5-
– Remove exterior mirror -1- in direction of -arrow A-. When
doing this, guide grommet -6- with electrical wire in direction
of -arrow B- out of door -2-.
Installing
Install in reverse order of removal, observing the following:
– Use an insertion aid to guide grommet with electrical wire
into door.
Tightening torques
♦ ⇒ Rep. gr. 66; Assembly overview – exterior mirror
7.3
Removing and installing mirror glass
Special tools and workshop equipment required
♦ removal lever -80-200-
Removal and installation are described for the left side of vehi‐
cle as an example.
Removing
CAUTION
Risk of injury to hands and eyes caused by glass splinters.
Risk of cuts.
– Wear safety goggles.
– Wear protective gloves.
NOTICE
Risk of damage to component surfaces.
– Before using a lever, always mask off the components
installed in visible areas using commercially available ad‐
hesive tape.
– Press bottom of mirror glass -1- into mirror housing.
254
Rep. gr.66 - Exterior equipment
ID.4 2021 ➤
General body repairs, exterior - Edition 05.2021
– Use removal lever -80-200--4- to lever mirror glass -1- off
mirror adjustment unit -2-.
– Swing mirror glass -1- in direction of -arrow A-, and discon‐
nect electrical connectors -3-.
Installing
Install in reverse order of removal, observing the following:
– Push mirror glass centrally onto mirror adjustment unit until it
can be heard to engage.
Note
When fitting the mirror glass, apply force only in centre of mirror
glass.
– Perform functional check.
7.4
Removing and installing mirror adjust‐
ment unit
Removal and installation are described for the left side of vehi‐
cle as an example.
Removing
– Remove mirror glass ⇒ Rep. gr. 66; Removing and installing
mirror glass.
– Unscrew bolt -3-, and remove mirror adjustment unit -1-.
7. Exterior mirror
255
ID.4 2021 ➤
General body repairs, exterior - Edition 05.2021
– Disconnect electrical connector -2-.
Installing
Install in reverse order of removal, observing the following:
Tightening torques
♦ ⇒ Rep. gr. 66; Assembly overview – exterior mirror
7.5
Removing and installing mirror cover
7.5.1
Removing and installing upper mirror
cover
Removal and installation are described for the left side of vehi‐
cle as an example.
Removing
– Remove mirror frame ⇒ Rep. gr. 66; Removing and installing
mirror frame.
– Carefully push upper mirror cover -1- in direction of
-arrow A-.
– Pull mirror cover -1- in direction of -arrow B- off mirror
mounting.
Installing
Install in reverse order of removal.
256
Rep. gr.66 - Exterior equipment
ID.4 2021 ➤
General body repairs, exterior - Edition 05.2021
7.5.2
Removing and installing lower mirror
cover
Removal and installation are described for the right vehicle side
as an example.
Removing
– Remove upper mirror cover ⇒ a7.5.1 nd installing upper mir‐
ror cover”, page 256 .
– Release locking devices -arrows-.
– Remove lower mirror cover -1- in direction of -arrow A- from
mirror mounting.
Installing
Install in reverse order of removal, observing the following:
– Push on lower mirror cover until locking devices can be
heard to engage.
7.6
Removing and installing mirror frame
Removal and installation are described for the left side of vehi‐
cle as an example.
Removing
– Remove mirror glass ⇒ Rep. gr. 66; Removing and installing
mirror glass.
– Unscrew bolts -2-.
7. Exterior mirror
257
ID.4 2021 ➤
General body repairs, exterior - Edition 05.2021
– Release fasteners -3- -arrows A-.
– Pull off mirror frame -1- in direction of -arrow B-.
Installing
Install in reverse order of removal, observing the following:
Tightening torques
♦ ⇒ Rep. gr. 66; Assembly overview – exterior mirror
258
Rep. gr.66 - Exterior equipment
2024 VW ID.4 Owner's Manual
