ID.4 2021 ➤
General body repairs, exterior - Edition 05.2021
3
Wings
3.1
Assembly overview – wing
The overview is shown for the left side of vehicle as an exam‐
ple.
1 - Wing
❑ ⇒ Rep. gr. 50; Remov‐
ing and installing wing
2 - Bolt
❑ qty. 11 on each side
❑ 8 Nm
3 - Bolt
❑ qty. 1 on each side
❑ 6 Nm
4 - Insulation for wing, upper
section
5 - Insulation for wing, lower
section
6 - Centre hex stud
❑ qty. 2 on each side
❑ 8 Nm
7 - Wing bracket
❑ ⇒ Rep. gr. 50; Remov‐
ing and installing wing
bracket
8 - Bracket for deformation el‐
ement
❑ ⇒ a3.5.2 nd installing
bracket for deformation
element”, page 10
9 - Wing bracket
❑ ⇒ a3.5.1 nd installing
wing bracket”, page
10
10 - End plate
❑ ⇒ Rep. gr. 50; Remov‐
ing and installing end plate
3.2
Removing and installing wing
Special tools and workshop equipment required
♦ setting gauge -3371-
Removal and installation are described for the left side of vehi‐
cle as an example.
Removing
– Remove seal for plenum chamber cover ⇒ Rep. gr. 50; Re‐
moving and installing plenum chamber cover.
6
Rep. gr.50 - Body - front
ID.4 2021 ➤
General body repairs, exterior - Edition 05.2021
– Remove plenum chamber cover at side ⇒ Rep. gr. 50; Re‐
moving and installing plenum chamber cover.
– Remove front bumper cover ⇒ Rep. gr. 63; Removing and
installing bumper cover.
– Remove headlight ⇒ Electrical system; Rep. gr. 94; Head‐
light; Removing and installing headlight.
– Remove A-pillar trim ⇒ Rep. gr. 66; Removing and installing
A-pillar trim.
– Unscrew bolt -2-
– Unscrew centre hex studs -4-.
– Pull off end plate -5- slightly in area of bolt -6-.
– Unscrew bolts -3-.
– Remove wing -1- carefully.
Installing
If new A-pillar is fitted
– Insert pop rivet nuts -1-.
Continue installation in reverse order of removal, observing the
following:
All vehicles (continued)
– Align wing free of tension with wing bracket loosened ⇒ Rep.
gr. 50; Removing and installing wing bracket.
3. Wings
7
ID.4 2021 ➤
General body repairs, exterior - Edition 05.2021
– Verify gaps using setting gauge -3371-. Observe ⇒ Body
Repairs; Rep. gr. 00; Panel gaps; Body – front, when doing
this.
Tightening torques
♦ ⇒ Rep. gr. 50; Assembly overview – wing
3.3
Removing and installing end plate
Removal and installation are described for the left side of vehi‐
cle as an example.
Removing
– Remove front door ⇒ Rep. gr. 57; Removing and installing
door.
– Remove front wheel housing liner ⇒ Rep. gr. 66; Removing
and installing front wheel housing liner.
– Release locking devices -2-.
– Slight pull end plate -1- at top in direction of -arrow A- off
wing -3-, and pull it out in direction of -arrow B-.
Installing
– Insert end plate -1- in direction of -arrow a- at wing -2-.
8
Rep. gr.50 - Body - front
ID.4 2021 ➤
General body repairs, exterior - Edition 05.2021
– Push end plate -1- in direction of -arrow B- against wing -2-
until locking devices -3- engage.
Important
•
The lower locking device -3- must engage in wing bracket
-4-.
Continue installation in reverse order of removal.
3.4
Removing and installing wing bracket
Removal and installation are described for the left side of vehi‐
cle as an example.
Removing
– Remove wing ⇒ Rep. gr. 50; Removing and installing wing.
– Unscrew bolts -2-.
– Remove wing bracket -1-.
Installing
Install in reverse order of removal, observing the following:
– Adapt wing bracket and wing to bonnet and bumper ⇒ Body
Repairs; Rep. gr. 00; Body panel gaps/shut lines; Body –
front.
Tightening torques
♦ ⇒ Rep. gr. 50; Assembly overview – wing
3. Wings
9
ID.4 2021 ➤
General body repairs, exterior - Edition 05.2021
3.5
Removing and installing wing bracket
3.5.1
Removing and installing wing bracket
Removal and installation are described for the left side of vehi‐
cle as an example.
Removing
– Remove wing ⇒ Rep. gr. 50; Removing and installing wing.
– Unscrew bolt -2-
– Remove for wing bracket -1-.
Installing
Install in reverse order of removal, observing the following:
Tightening torques
♦ ⇒ Rep. gr. 50; Assembly overview – wing
3.5.2
Removing and installing bracket for de‐
formation element
Removal and installation are described for the left side of vehi‐
cle as an example.
Removing
– Remove wing ⇒ Rep. gr. 50; Removing and installing wing.
– Unscrew bolts -2-.
– Remove bracket for deformation element -1-.
Installing
Install in reverse order of removal, observing the following:
10
Rep. gr.50 - Body - front
ID.4 2021 ➤
General body repairs, exterior - Edition 05.2021
– Adapt bracket for deformation element and wing to bonnet
and bumper ⇒ Body Repairs; Rep. gr. 00; Body panel gaps/
shut lines; Body – front.
Tightening torques
♦ ⇒ Rep. gr. 50; Assembly overview – wing
3. Wings
11
2024 VW ID.4 Owner's Manual
