ID.4 2021 ➤
General body repairs, exterior - Edition 05.2021
5
Side windows
5.1
Assembly overview – rear side windows
The overview is shown for the left side of vehicle as an exam‐
ple.
1 - Rear side window
❑ ⇒ Rep. gr. 64; Remov‐
ing and installing rear
side window
2 - Seal
❑ Can be renewed only
together with rear side
window
3 - PUR adhesive sealant
4 - Body flange
5 - Clip
❑ qty. 3
5.2
Removing and installing rear side win‐
dow
5.2.1
Removing and installing rear side win‐
dow
Special tools and workshop equipment required
♦ awl -V.A.G 1474/2-
♦ cutting cord -VAS 861 001/1A-
♦ pull handle -V.A.G 1351/1-
194
Rep. gr.64 - Glazing
ID.4 2021 ➤
General body repairs, exterior - Edition 05.2021
♦ reel device -V.A.G 1654A-
♦ removal kit for flush bonded windows -VAS 6452-
♦ removal kit for flush bonded windows -V.A.G 1474B-
Removal and installation are described for the left side of vehi‐
cle as an example.
Removing
The description for the removal of the side window is based on
the removal kit for flush bonded windows -V.A.G 1474B-.
The removal kit for flush bonded windows -VAS 6452- may also
be used.
– Remove luggage compartment side trim ⇒ General body
repairs, interior; Rep. gr. 70; Luggage compartment trims;
Removing and installing luggage compartment side trim.
NOTICE
Risk of damage to component surfaces.
– Mask off surrounding components in the visible area with
commercially available adhesive tape.
– Use awl -V.A.G 1474/2--2- to pull cutting cord -VAS 861
001/1A--1- through adhesive sealant, as shown in illustra‐
tion.
– Push aside seal.
– Use tube -1- to insert cutting cord -VAS 861 001/1A--3- be‐
hind seal in window flange.
– Secure end of cutting cord -VAS 861 001/1A--1- to pull han‐
dle -V.A.G 1351/1--2- for counterholding.
5. Side windows
195
ID.4 2021 ➤
General body repairs, exterior - Edition 05.2021
– Pull other end of cutting cord -VAS 861 001/1A-
through adhesive sealant, and secure it to reel device -
V.A.G 1654A--3-.
In the area of the clips -4-, greater force is required.
– Move reel device -V.A.G 1654A--3- to cut free rear side
window.
– Use plastic wedge to push cutting cord -VAS 861 001/1A-
against window while cutting free to ensure sufficient clear‐
ance to window flange.
Installing
– ⇒ Rep. gr. 64; Prepare old undamaged windows for instal‐
ling.
– ⇒ Rep. gr. 64; Prepare new windows for installing.
– ⇒ Rep. gr. 64; Prepare body flange for installing.
– ⇒ Rep. gr. 64; Installation instructions for bonded windows.
– ⇒ Rep. gr. 64; Minimum drying times for bonded windows.
– Guide rear side window with seal -1- in direction of -arrow A-
into guide -3-, and push it on.
– Secure rear side window using adhesive tape.
5.2.2
Removing broken rear side window
A broken rear side window is removed in the same manner as a
broken rear window ⇒ b4.2.2 roken rear window”, page 192 .
196
Rep. gr.64 - Glazing
ID.4 2021 ➤
General body repairs, exterior - Edition 05.2021
6
Door windows
6.1
Assembly overview – front door win‐
dow
6.1.1
Assembly overview – front door window
The overview is shown for the left side of vehicle as an exam‐
ple.
1 - Front door window
❑ ⇒ Rep. gr. 64; Remov‐
ing and installing front
door window
2 - Assembly carrier
❑ ⇒ Rep. gr. 57; Assem‐
bly overview – assem‐
bly carrier
3 - Cap
❑ qty. 2
4 - Window regulator clamp‐
ing jaw
❑ qty. 2
6.1.2
Assembly overview – fixed front door window
The overview is shown for the left side of vehicle as an exam‐
ple.
6. Door windows
197
2024 VW ID.4 Owner's Manual
