ID.4 2021 ➤
Electrical system - Edition 02.2021
– Unscrew bolts -2-.
– Guide LED module for daytime running light -1- out of head‐
light housing until electrical connector is accessible.
– Disconnect electrical connector.
– Remove LED module for daytime running -1-.
Installing
Install in reverse order of removal, observing the following:
NOTICE
Risk of destroying headlight due to ingress of water.
– Check seal between LED module for daytime running and
headlight for damage.
– Make sure seal is properly seated.
– Check headlight settings and adjust headlights if necessary
⇒ Maintenance; Booklet 53.1; Descriptions of work.
Tightening torques
♦ ⇒ Rep. gr. 94; Assembly overview – headlight
2.10
Removing and installing bulb for VARI‐
LIS headlight [L207]/[L208]
Special tools and workshop equipment required
♦ ESD workplace -VAS 6613-
♦ Torque screwdriver -V.A.G 1624-
The front left headlight -MX1- and front right headlight -MX2-
will henceforth be referred to as “headlight”.
2. Headlights
71
ID.4 2021 ➤
Electrical system - Edition 02.2021
The bulb for left VARILIS headlight -L207- and bulb for right
VARILIS headlight -L208- will henceforth be referred to as “bulb
for VARILIS headlight”.
Removal and installation are described for the left vehicle side
as an example.
Removing
– Remove headlight ⇒ Rep. gr. 94; Removing and installing
headlight.
NOTICE
Risk of damage to electrical components.
Electrostatic charge may damage electrical components.
– Work on electrical components must always be carried out
at an ESD workplace.
– Place headlight onto ESD workplace -VAS 6613-.
– Use a hammer to carefully release housing cover -1- along
predetermined break line -2-.
– Remove housing cover -1- from headlight.
– Disconnect electrical connector -2-.
72
Rep. gr.94 - Lights, bulbs, switches - exterior
ID.4 2021 ➤
Electrical system - Edition 02.2021
– Pull off retainer for electrical wires -4-.
– Release locking devices -3-.
– Remove electrical wires from retainer -1-.
– Release locking lugs -6-.
– Remove electrical connector -5-.
– Unscrew bolts -2-.
– Guide bulb for VARILIS headlight -1- out of headlight hous‐
ing until electrical connector -3- is accessible.
– Disconnect electrical connector -3-.
– Remove bulb for VARILIS headlight -1-.
Installing
Install in reverse order of removal, observing the following:
2. Headlights
73
ID.4 2021 ➤
Electrical system - Edition 02.2021
NOTICE
Risk of destroying headlight due to ingress of water.
– When installing the housing cover -1-, make sure that the
seal is correctly seated.
Note
A new housing cover -1- must be used only, if the repair is
carried out for the first time.
– Fit housing cover -1- on headlight.
– Tighten bolts -2-.
– Check headlight settings and adjust headlights if necessary
⇒ Maintenance; Booklet 53.1; Descriptions of work.
Tightening torques
♦ ⇒ Rep. gr. 94; Assembly overview – headlight
2.11
Removing and installing headlight fan
[V407]/[V408]
Special tools and workshop equipment required
♦ ESD workplace -VAS 6613-
♦ Torque screwdriver -V.A.G 1624-
The front left headlight -MX1- and front right headlight -MX2-
will henceforth be referred to as “headlight”.
The left headlight fan -V407- and right headlight fan -V408- will
henceforth be referred to as “headlight fan”.
Removal and installation are described for the left vehicle side
as an example.
Removing
– Remove headlight ⇒ Rep. gr. 94; Removing and installing
headlight.
NOTICE
Risk of damage to electrical components.
Electrostatic charge may damage electrical components.
– Work on electrical components must always be carried out
at an ESD workplace.
– Place headlight onto ESD workplace -VAS 6613-.
74
Rep. gr.94 - Lights, bulbs, switches - exterior
2024 VW ID.4 Owner's Manual
