ID.4 2021 ➤
Electrical system - Edition 02.2021
1 - Bracket for control
unit 2 for break-in protec‐
tion -J1192-/control unit 3 for
break-in protection -J1193-
2 - Control unit 2 for break-
in protection -J1192-/control
unit 3 for break-in protection
-J1193-
❑ ⇒ a8.8 nd installing
control unit 2 for break-
in protection [J1192]/
control unit 3 for break-
in protection [J1193]”,
page 104
3 - Bolt
❑ qty. 2
❑ 2 Nm
8.4
Removing and installing interface for
entry and start system [J965]
8.4.1
Removing and installing interface for
entry and start system [J965], left-hand
drive vehicles
The interface for entry and start system -J965- will henceforth
be referred to as “interface for entry and start system”.
If the interface for entry and start system unit is renewed, per‐
form the test plan for the renewal of the interface for entry and
start system using ⇒ Vehicle diagnostic tester.
Removing
– Remove driver side footwell cover ⇒ General body repairs,
interior; Rep. gr. 68; Compartments/covers; Removing and
installing driver side footwell cover.
– Disconnect electrical connector -2-.
100
Rep. gr.94 - Lights, bulbs, switches - exterior
ID.4 2021 ➤
Electrical system - Edition 02.2021
– Release locking lug -3-.
– Swing out interface for entry and start system -1- in direction
of -arrow A-.
Installing
Install in reverse order of removal, observing the following:
– The entry and start authorisation control unit must be heard
to engage.
– If the interface for entry and start system unit has been
renewed, conclude the test plan for the renewal of the inter‐
face for entry and start system using ⇒ Vehicle diagnostic
tester.
8.4.2
Removing and installing interface for
entry and start system [J965], right-
hand drive vehicles
The interface for entry and start system -J965- will henceforth
be referred to as “interface for entry and start system”.
If the interface for entry and start system unit is renewed, per‐
form the test plan for the renewal of the interface for entry and
start system using ⇒ Vehicle diagnostic tester.
Removing
– Remove footwell vent on driver side ⇒ Heating, air condition‐
ing system; Rep. gr. 87; Air duct system; Removing and
installing footwell vent on driver side.
– Unscrew bolts -2-.
– Remove interface for entry and start system -1- until electri‐
cal connector is accessible.
– Disconnect electrical connector -3-.
– Remove interface for entry and start system -1-.
8. Entry and start authorisation system
101
ID.4 2021 ➤
Electrical system - Edition 02.2021
Installing
Install in reverse order of removal, observing the following:
– If the interface for entry and start system unit has been
renewed, conclude the test plan for the renewal of the inter‐
face for entry and start system using ⇒ Vehicle diagnostic
tester.
Tightening torques
Component
Specified torque
Bolts for interface for entry and 8 Nm
start system
8.5
Removing and installing entry and start
authorisation aerial [R200]/[R201]
The left aerial for entry and start authorisation -R200- and right
entry and start authorisation aerial -R201- will henceforth be
referred to as “aerial”.
Removal and installation are described for the left vehicle side
as an example.
Removing
– Remove front wheel housing liner ⇒ General body repairs,
exterior; Rep. gr. 66; Wheel housing liner; Removing and
installing front wheel housing liner.
– Disconnect electrical connector -1-.
– Release locking lugs -2- using an 8 mm socket.
– Remove aerial -3-.
Installing
Install in reverse order of removal, observing the following:
Tightening torques
♦ ⇒ General body repairs, exterior; Rep. gr. 66; Wheel housing
liner; Assembly overview – front wheel housing liner
102
Rep. gr.94 - Lights, bulbs, switches - exterior
2024 VW ID.4 Owner's Manual
