ID.4 2021 ➤
Electrical system - Edition 02.2021
– Use a commercially available plastic wedge to unclip trim
-1-.
– Disconnect electrical connector -2-.
– Secure display unit for driver information system against fall‐
ing out.
– Unscrew bolts -1-.
– Remove display unit for driver information system.
Installing
Install in reverse order of removal, observing the following:
Tightening torques
♦ ⇒ Rep. gr. 90; Assembly overview – control unit with display
unit for driver information system
2.4
Removing and installing control unit for
head-up display [J898]
Special tools and workshop equipment required
♦ Torque screwdriver -V.A.G 1624-
The control unit for head-up display -J898- will henceforth be
referred to as “control unit for head-up display”.
The dynamic light strip 1 for information in dash panel -L385-
will henceforth be referred to as “dynamic light strip”.
If the control unit for head-up display is renewed, perform the
test plan for the renewal of the control unit for head-up display
using ⇒ Vehicle diagnostic tester.
Removing
– Remove windscreen ⇒ General body repairs, exterior; Rep.
gr. 64; Windscreen; Removing and installing windscreen.
22
Rep. gr.90 - Gauges, instruments
ID.4 2021 ➤
Electrical system - Edition 02.2021
– Remove dynamic light strip ⇒ a2.12 nd installing dynamic
light strip 1 for information in dash panel [L385]”, page 124 .
– Remove head-up display cover ⇒ General body repairs, inte‐
rior; Rep. gr. 70; Dash panel; Removing and installing dash
panel trim.
– Place dash panel insulation to one side.
– Cover control unit for head-up display -1- with a soft cloth.
– Unscrew bolts -arrows-.
– Remove control unit for head-up display -1- until the electri‐
cal connectors are accessible.
– Disconnect electrical connectors.
– Remove control unit for head-up display -1-.
Installing
Install in reverse order of removal, observing the following:
If the control unit for head-up display has been renewed.
– On new part, unscrew bolts -2-.
– Remove actuator plates -3- from control unit for head-up
display -1-.
Note
These work steps are necessary to avoid calibration of the con‐
trol unit for head-up display.
2. Dash panel insert
23
ID.4 2021 ➤
Electrical system - Edition 02.2021
All vehicles (continued)
NOTICE
Risk of damage to control unit for head-up display.
– Never apply pressure to the upper part of the housing
when inserting.
– Should a control unit for head-up display fall down, it must
be renewed.
– Insert control unit for head-up display -1-.
– Connect electrical connectors.
– Tighten bolts -arrows-.
– Position windscreen and secure it temporarily with adhesive
tape – do not bond it in yet.
– Switch on ignition.
– Perform functional check.
– Install windscreen ⇒ General body repairs, exterior; Rep.
gr. 64; Windscreen; Removing and installing windscreen.
– Calibrate control unit for head-up display ⇒ Rep. gr. 90;
Calibrating control unit for head-up display [J898].
Tightening torques
Continue installation in reverse order of removal, observing the
following:
♦ ⇒ Rep. gr. 90; Assembly overview – head-up display
2.5
Calibrating control unit for head-up dis‐
play [J898]
2.5.1
Calibrating control unit for head-up dis‐
play [J898], left-hand drive vehicles
Special tools and workshop equipment required
♦ calibration board for head-up display AR -VAS 721 019-
24
Rep. gr.90 - Gauges, instruments
2024 VW ID.4 Owner's Manual
